Power Acoustik Popular Questions, Answers, Tips & Manuals

Here is a link to Power Acoustik support page:http://www.poweracoustik.com/pa2006/OWNER_MANUAL.htm#current pd From the Amplifier drop down list, select "Lightning Series 03-07" or let me know your email and ill send you the PDF myself.
dreamsystems

Nice amp.....the lights are turning on? Did you double checek that all speakers and connections are properly hoooked up. If you are getting power and have a proper ground, there should be no issues. Ensure all other wires are hooked up (to and from your deck, speakers etc.)

where do you live?

Del corriente de la bateria al positivo del capacitior. De la tiera de capacitor al positivo o corriente del amplificador. Bueana suerte.

Try tuning it in manually then press and hold the relevant preset button till it beeps or stores the frequency.
I hope I have been of help but please do not hesitate to ask if you have any further questions.
I appreciate your vote if you appreciate my reply and remember, even if you don't vote for me a
please and thank you goes a long way.

This could be due to one of a couple things:
- Speaker wires shorting out against each other (or the speaker may be shorted out itself)
- Not enough current coming through the power wire (check power connection, ensure you are using big enough wire, i.e. 4awg)
- Not grounded well enough (check ground connection, make sure chassis ground is against bare metal and solid)

Does your fuse blow when volume turned up, or does it blow straight away when turned on? What watt is your subs and amp?

Honestly, if you have to ask, you should have a pro do it for you.
The few bucks you spend on installation may save a lot of money in burned out woofers and amps and wires etc.etc.

you probably have a blown sub(s) that short out when the volume is turned up. it would be a good idea to find out which one(s) is bad and replace it. sooner or later it may make the amp go bad if not replaced or removed.

If you are 100% sure that you have checked all the wiring, this is usually due to not enough current reaching the amp. Make sure you are using the right size power wire (4awg) and that the power and ground connections are solid. This could also be due to a bad ground to the chassis.

get it at best buy

Are you fused close to the battery with a 30-50 amp fuse block?
Ground unit also to most closest suitable location!
Is your power wire undersized?
Check units fuses you may have blown one hooking it up!!
Good luck

try putting a laser disc cleaner through the player it will clean the lazer allowing it to read correctly



best of luck

Hi, are you using the blue wire from the head unit to turn on the amp? The turn on voltage is more like 5 volts--not battery voltage, so you have to use the blue wire to turn on many amps.

Stereo device has been installed least powering off when vehicle turns off. In such a situation, either as manufacturer default of installation experts maladjustments. Observe the device that buttons makes power off without vehicles ignition. Two alternatives makes the devices rediscover the user's experience. First, discovering that the device powers with button becomes convenient. Else, arranging reinstallation of device to capture an impression. In a situation that the device least has the versatility features to capture power off from drivers ignition requires acquiring an alternate device.

Unfortunately it's not that simple : the drive lock is done thru an electronic command - the player gets this information from the ECM, not just a simple Park wire.
To make it work the entire wiring of the player must be modified - a fiddly job that must be left to a pro shop (if you can find one that is willing to do it - illegal and severely punishable). Unless of course you want to do it yourself and risk frying the entire electronics of the car.

try checking your speakers and speaker wires for shorts and/or grounds.

check the rca cables on the back to see if you might have the sub woofer cable in wrong rca spot

this is how it should be wired from your radio front output a set of rca cables go to the radio input of the eq. if you have sub out on radio it will not be used ... eq takes place of it ... turn off subout on radio ... to use eq or preamp you must have at 2 amps 1 for mids and tweets and 1 for subs to work eq right

then from the eq you have another set of rca cables comming from the front output to your mids and tweet amp and then if you dont have a second amp u wont need rear output move over to the suboutput and run a set of rca cables from eq's sub output to sub amp this is how the audio cable section should be connected if you still dont get it to work proper then then it has a electronic issue and need to warranted out if still in warranty or buy new one .... here is a link to the install manual with a wire diagram for repair shop .....http://www.poweracoustik.com/pa2006/manual%20and%20catalog/Processors/PWM-20.pdf

Please replace the screen then. It is very hard to get repaired.
Regards, Jay

You need to check Constant power, Ground, and also the remote turn onwith a 12v power
if all this seems fine then it seems like your amp is damaged


PS
check the fuses right next to the amp that might also fix it