Polder Hardware & Accessories - Page 6 - Recent Questions, Troubleshooting & Support

To set your Garrison timer model 52-8817-6 to operate properly, you may need to adjust the time and the mode settings. Here are the steps you can follow:

1. First, set the correct time on the timer. To do this, locate the "TIME" button and hold it down until the hour digits start to flash. Use the "+" and "-" buttons to adjust the hour, then press the "TIME" button again to move to the minute digits. Repeat the same process to set the correct minutes.
2. Once you have set the correct time, you can then set the mode. To do this, locate the "MODE" button and press it until the desired mode is displayed. In your case, you will want to set the timer to the "PM" mode.
3. Finally, set the on and off times for your device. To do this, locate the "PROG" button and press it to enter programming mode. Use the "+" and "-" buttons to set the on and off times for each day of the week.

If you have followed these steps and your timer is still not operating properly, you may need to consult the user manual or contact the manufacturer for further assistance.

You either have the time of day set wrong, or the Timer On/Off time is set wrong. https://www.google.com/search?q=garrison+52-8817-6+manual ..

This usually means that the batteries need to be replaced. Make sure you check the type of batteries needed for your timer, and replace them according to the instructions. If the issue persists after replacing the batteries, you may need to contact the manufacturer or a qualified technician for further assistance

It sounds like the program settings may not be saved correctly. You may want to try resetting and reprogramming the device to see if that fixes the issue. If not, it is possible that there could be a problem with the circuit board or the unit may need to be serviced if the issue persists.

It is possible that the issue could be related to the timer, however it may also be worth trying to reset the unit to the factory settings. This could help to clear up any lingering issues with the unit's settings that may be preventing it from running properly. If the issue persists after resetting, then you may need to check the timer or contact a qualified technician for further assistance.

The black line wire connects to the negative (-) terminal on the circuit board. You may find wiring diagrams for specific products online, or you can reach out to the manufacturer for detailed instructions.

It looks like Vigoro does not sell replacement battery housings for their water timers. You may want to check with local stores or online retailers to see if they have the battery housing in stock, as well as third-party suppliers. Alternatively, you could consider investing in a new water timer with a different design that does not require a battery housing.

No indication of 'make model (what it is)', so difficult to give a definitive answer. Remove power from mains or batteries on the MYSTERY item. https://www.google.com/search?q=Timer+won%27t+stop+beeping+when+unit+is+off ..

Remove the batteries for an hour.

the unit requires a 30 amp beaker and 10 AWG wire. If wired correctly i would suspect shorted heating element.

It is not clear which product you have. Attach photo of timer for clear identification by expert. Otherwise following link has resources to help identify common timers http://waterheatertimer.org/How-to-set-timers.html http://waterheatertimer.org/Intermatic-timers-and-manuals.html http://waterheatertimer.org/Woods-timers-and-manuals.html Gene Water Heater Timers Save Money If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Question edited for clarity, guess at what you have, not a Chevy Malibu? Question moved from Microwaves to Timers. Reset buttons on timers remove all set On/Off programs in a long press of the buttons. https://www.google.com/search?q=Malibu+voltage+transformer%2C+press+to+reset

Suena como si pudiera haber un problema con el transmisor de su radio Cobra 200 GTL N9. Es posible que la fuente de alimentaci?n de la radio no est? proporcionando suficiente energ?a al transmisor, o que el transmisor no est? conectado correctamente. Debe verificar la fuente de alimentaci?n para asegurarse de que est? conectada y proporcione el voltaje y la amperaje correctos a la radio. Tambi?n debe verificar todas las conexiones entre el transmisor y la radio, incluidos el cable de antena y el cable del micr?fono. Si las conexiones est?n seguras y la fuente de alimentaci?n funciona correctamente, entonces el problema puede estar con la radio misma y es posible que necesite ser atendida por un profesional.

It sounds like there may be an issue with the timer itself. Some things you can try include double-checking that the timer is set up correctly and ensuring that the power supply to the timer is stable. You can also try cleaning the contacts on the timer, as dirt or corrosion on the contacts can prevent the timer from functioning properly. If these steps do not help, it is possible that the timer is malfunctioning and may need to be replaced. If you have tried these steps and the timer is still not working as expected, you may want to consider contacting the manufacturer or a professional for further assistance.

Just reprogramme it

Hi, It seems like your device is being sold on websites like amazon and ebay. Your best move might be to request the instructions from one of those sellers and ask them to send it to you as an individual product. Otherwise, you might have to reach out the librarian at a local college or technical college to ask if they could provide you the instructions that you're seeking. Thank you.

OK, even though the thread is old, I had to add my answer, to clarify things. Settings: F = Switch is Off O = Switch is constantly On (no timer mode) d = Switch turns On at Dusk, and turns Off at Dawn 1-9 = Switch turns On at Dusk, and turns Off after the number of hours shown in the display 1.-9. = Switch turns On immediately, and turns Off after the number of hours shown in the display

This timer is made by Living Solutions. It's best to set the timer prior to plugging it in. To set current time: Lift protective cover and set the current time by rotating dial CLOCKWISE until the arrow on the side of dial aligns with the correct time. Note: Timer dial will rotate COUNTER-CLOCKWISE when operating. To set timer: Move timer arms (located around the dial) towards the middle of the dial for the time you would like the timer OFF. Move the arms towards the outside of the dial for the time you would like the timer ON. Release protective cover.

Please check the link for the Manual https://images.homedepot-static.com/catalog/pdfimages/06/060c891b-9c12-4311-ad3f-41f6cec89d87.pdf

https://www.google.com/search?q=368-1740+power+stake+manual