Planar Answered Questions & Fixed Issues

1. Try a different DVI cable. 2. Check the monitor's settings and make sure it is set to the correct resolution. 3. Try a different computer or laptop to see if the issue is with the computer or the monitor. 4. Try a different DVI port on the computer. 5. Try a different monitor. 6. Check the video card settings and make sure it is set to the correct resolution. 7. Try a different video card

Make sure it is on level ground.

We supply original projector parts: lamp, bulb, Lcd panel, Lens, DMD chip, color wheel, motherboard, powersupply ... with high quality and competitive price. Jerry Lampdeng Limited

Here is the user's guide for your monitor: (from Planar's website) http://www.planar.com/media/222919/mn-planar-px2710mw.pdf

here is the user's guide for your touch-screen monitor : (from Planar's website) http://www.planar.com/media/87916/mn-planar-pt1700-01-m-mu.pdf

Planar PL LCD Monitor Fix - MarsBox.com

marsbox.com > Blog > Howtos

Nov 3, 2008 - Planar PL LCD monitor has flashing power led with no image. ... You will know it worked if the monitor diplays "No Signal" message when ...

What is the method to reset the Planar 1910m monitor?

superuser.com/.../what-is-the-method-to-reset-the-planar-1910m-monitor

Apr 6, 2010 - My monitor (a Planar, apparently model number PL1910M) is not working. (It is flashing a green / orange sequence which I believe to be an error code. The sequence, in ... I wasn't even seeing a "no signal" message and I couldn't turn it off using the power button. ... Computer resets when put under load.

ViewSonic VX922 monitor - black screen - green power light flashes ...

www.tomshardware.com > Forum > Displays

Tom's Hardware Guide Feb 1, 2008 - 50 posts - ‎27 authors Repair ViewSonic VX924 LCD Monitor Blinking Green power Button ... cant switch back & forth to desktop out of some games without the monitor going .... Nothing else on the board looks bad, the power supply board is dark brown ... to this madness we are unfortunantly dealing with daily with our monitors.Missing: planar ‎pl1700

No, there is no microphone listed in the specs, just integrated speakers

replace/repair the touchscreen glass / controller

I use either VGA or HDMI connectors to connect to an external monitor. I'm not sure what you're asking on the "power cord". Are you asking about the charging "brick" and such? Or?

You will need to go to advanced settings under resolution options and set the display to 60hz refresh rate then go back to resolution and set your native, the problem is its probably trying to default to 75hz and is causing an issue

Does anyone know where to find this board? My firewire connector broke off. Or can anyone soder it back on? Best Regards William

try the capasitos in the in line of the circuit they have to be electrolitic condencer some times with the time they open and made the monitor not work try it wiht analog multimeter is more easer know if the condencer are bad

Try Another Monitor---If OK--Problem Is With Your Monitor---If Does The Same Thing--Problem With Computer Video.

eBay..... search for DX2, and also under Planar Dome. You'll need the software from ndssi.com, under the cx section.

Only the Planar Dome DX2 card..... no other. Planar did this on purpose to sell those cards at 2k each. Now very reasonably priced on eBay, but they'll only work on XP, not W7.

For your Plana Dome C3i you can get the drivers and CXtra calibration software under the cx section at ndssi.com. You must use a DX2 card (eBay) and XP. No go on W7 for those.

Not possible.... same as with the C5i I posted on. By the way, you don't need a dual link cable to run either the C3i or the C5i with the DX2 card..... single link DVI only is fine.

perhaps this

Picture tube. Trash it get new.

The Planar PX2210MW is notorious for bad electrolytic capacitors. Specifically capacitor C804 on the power supply board. . This is a 1000uF 25volt capacitor. That capacitor was usually made by Hermei and it was purple. Normally, the top of a capacitor will be flat. When it fails, it will be curved upward and there may be some brown material leaking out. If the monitor still will not work after replacing C804, the problem could be Q805 or Q806. These are located on the under side of the board. They are small black surface mounted chips. There are 8 pins on these chips. I have seen both AO4620 and APM4548A part numbers used. These chips contain a pair of MOSFET transistors. One transistor is n-channel and the other is p-channel. Look for a short in one of the transistors. I have repaired several of these monitors. C804 is always bad. How ever, in three cases, Q805 or Q806 was also bad