PfaFF Popular Questions, Answers, Tips & Manuals

Fut Munten https://nl.FIFAcoin.com FIFA 19 Munten https://nl.FIFAcoin.com/category-robosystem20-FIFA-19-coins.html FIFA Munten https://nl.FIFAcoin.com FIFA 19 Munten PS4 https://nl.FIFAcoin.com/category-robosystem20-FIFA-19-coins-ps4.html FIFA 19 Munten Xbox One https://nl.FIFAcoin.com/category-robosystem20-FIFA-19-coins-xboxone.html FIFA 19 Munten PC https://nl.FIFAcoin.com/category-robosystem20-FIFA-19-coins-pc.html FIFA 19 Munten Switch https://nl.FIFAcoin.com/category-robosystem20-FIFA-19-coins-switch.html FIFA 19 Paketten https://nl.FIFAcoin.com/futtot FIFA Munten Kopen https://nl.FIFAcoin.com Koop FIFA Munten https://nl.FIFAcoin.com Goedkope FIFA Munten https://nl.FIFAcoin.com

Hello, Sandie - You will find several images of how to thread your Pfaff Synchrotronic 1229 sewing machine in the instruction book for the machine, starting on Pages 6 - 9 (PDF images #10 - 13) of the manual (PDF format) here: http://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/Synchrotronic_1229-manual-EN.PDF Since it is a PDF document, you will need Adobe Acrobat Reader software (free), to download and save the document on your computer, and open and refer to it later. Note: When you save the PDF document to your computer, be sure to give the file a name you can find again easily . . . something like: Pfaff Synchrotronic 1229 Manual. Best wishes.

You need to lubricate all the bushing under the machine this is the problem, not the bobbin ! all the best.

Test the socket with an A/C meter set to line voltage range to see if the problem is there.

I would like to help you the best I could, but I think talking to a sewing machine technician at a sewing machine repair shop might be your best bet. It would probably be best to get your machine serviced since you haven't used it in three years.

Hello, Victoria - I suggest you locate an authorized Pfaff sewing machine repair business near you and take the machine there for evaluation and repair. Best wishes.

Once you open the top cover you can observe by turning the wheel manually where is the actual clutch mechanism location (by switching bobbin winding off and on). Once you see small dark element moving slightly on the inside of the wheel, drop a bit of oil on it and switch back and forth clutch by turning small knob. After few tries clutch started working perfectly.

Go back and check to make sure it is all threaded properly. You may have skipped a loop or gone around one backward.

turn the plate 180 degrees and try again

Most likely, Not. Not many machines made in that time period would have built-in walking feet. Pfaff 1222 buying guide part 1 (there is also a part 2) Manual: https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=2ahUKEwiCuNfv08TcAhUj6oMKHcdnDrYQFjAAegQIARAC&url=http%3A%2F%2Fwww.pfaff.com%2FSiteMedia%2FPFAFF%2FProducts%2FMachines%2FSupport-manuals%2Fpfaff_1221_1222-manual-EN.pdf&usg=AOvVaw3KuYqKVEFzbNGKVxg7Fzz6

-There’s a lever for the presser foot pressure, turn it to “1”.
-On that piece the lever is on to the rear, there’s also a white plastic flat head screw, turn it and that will release that side cover. (You’ll kind of still need to pry it off, it seemed a bit like I was going to break the plastic, but it comes off).
-Once it’s off and the inside part of the needle bar is exposed, turn the handwheel until the needle bar is at its top dead center position, revealing a smaller flathead screw that will be just above the light.
-Either tighten or loosen that screw to move the needle bar to correct height, which leaves exactly 11.5mm between the tip of the over-edge needle B and the top edge of the needle plate. I put an arrow on the pic I posted of where the screw I’m talking about is.
Hopefully that helps someone and makes sense.

Was it velcro with adhesive? The adhesive has gummed up the needle. Raise the presser foot, loosen the needle, and see if you can remove the bobbin from the machine. Once you get the bobbin loose, then most everything else can be clipped.

Free manual: http://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/Hobbylock-_787_788-manual-EN.PDF http://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/Hobbylock-_787_788-manual-EN.PDF

Phone numbers for Pfaff are at the last page of the operator's manual, and in other search results using https://www.google.com http://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/hobby_1122_32-manual-EN.pdf?ext=.pdf http://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/hobby_1122_32-manual-EN.pdf?ext=.pdf

Search for: Make Model manual

Hi did you mean the machine was just maintenanced? ( that is serviced?) If so you should take it back to the service shop and get them to fix it. If it was a friend then only trial and error will maybe fix it. :-)

Check out youtube.

It depends on which parts you need. One source of some Pfaff Tiptronic 2040 parts are available here: https://www.sewingpartsonline.com/pfaff-2040-sewing-machine-parts.aspx?sort.ss_cat_sort=desc&index=22 . Compatible presser feet are probably available from even more locations. I hope this helps. Cindy Wells

Looks like your machine is an older mechanical. Is it possible it has seized due to old oil? Have you regularly had your machine professionally serviced?

Take your machine for service.