Panasonic Lands Phones - Recent Questions, Troubleshooting & Support


Most likely the microphone hole at/near the bottom of the phone is clogged with dirt. If you are able to, then dissasemble the handset, find that opening and clean it out. If you're not that brave, maybe try cleaning the hole with a toothbrush. Don't stick anything into the hole as you may damage the microphone. Hop this helps!

Panasonic Lands... | Answered on Sep 17, 2020


Firstly, disconnect all devices / base unit from your landline. Then, using a mobile phone, dial your landline number. Does the ringing tone in the earpiece continue or does it stop after one ring? If it stops then you have a line problem which you need to report to your service provider.

Panasonic Lands... | Answered on Sep 03, 2020


Something not quite right with that model number. If it is connected to a base station, it is the model number of that you need not the model number of the handset. you also need all the letter and numbers correctly spaced and capitalised, Kxtsc909cid is not the same as KX-TSC-909

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00D1Wp9LMoO1pa4ghRuxlHeRiF0mw:1598720691167&q=manual+of+Panasonic+Kx+Tsc+909

Panasonic Lands... | Answered on Aug 29, 2020


you can contact the mobile service provider.........

Panasonic... | Answered on Aug 28, 2020


The message indicates the base part of the phone is not receiving power.

Panasonic Lands... | Answered on Aug 27, 2020


Could be phone Co. problem

Panasonic Lands... | Answered on Aug 27, 2020


Based on the documentation for the KX-T76XX phones, you can cancel the Call Forwarding by picking up the handset of your KX-T7630. Then press the FWD/DND button. Next press 0 to cancel all call forwarding. See page 17 of the manual here: https://www.ask-tsc.com/pdf/KX-T76xx.pdf . (You can also select to cancel call forwarding for external or internal incoming calls separately, if needed.)

If pressing 0 does not work, did you lock the extension? See page 18 for information on unlocking the extension. If that fails, contact your phone system administration. As far as I know, there is no global reset option available to users of an extension.

I hope this helps.

Cindy Wells

Panasonic Lands... | Answered on Aug 25, 2020


Press the Program button. enter 50 for call forwarding and press Enter. enter 2 and the number (ie 25551234) to forward ALL calls to the specified number. enter 3 and the number to forward when busy, 4 and the number to forward when there is no answer, and 5 and the number for when you're either busy or there is no answer. Hit Enter and then the Program button again.

Panasonic... | Answered on Aug 25, 2020


The situation is that a KX-TGA931T reads out "No link to base. Reconnect AC adapter". This is what I saw on one of the used handsets I recently acquired.Unplugging and replugging either AC adapter (base or peripheral) does nothing. But the other otherwise identical handset that recently arrived evidently had different firmware, which more helpfully read out (I may be paraphrasing) "Press Locator button base for 4 seconds, then press OK." This instruction may need just a little elaboration. On the base, the lower right silver button is labeled LOCATOR INTERCOM. On the handset the upper right rubber button may have "OK" on the LCD screen above it, so when it does, it is the OK button. First make sure the base is plugged in and that you have at least a little charge in the handset. Then press that LOCATOR button (for about 4 seconds) until it beeps. It will begin to beep periodically for several cycles. While it is in this beeping mode, press and hold that OK button until it beeps. If you let go too soon, the screen reads "Error!" so just try it again, and wait for the beep. After the beep the screen reads (I may be paraphrasing) "Registering handset." This takes a few seconds. Then it is registered and when you press TALK you'll get a dial tone. Now you don't have to pay $5 for a chat with Panasonic or have to download a manual's PDF (if they even have it) and have your internet search switched to Yahoo. I do not know how many handsets this base will take - now I have 6 registered to it.

Panasonic... | Answered on Aug 19, 2020


The blinking LEDs means it need to have it's ID reprogrammed. Press the Program button and then the station number (Station 1 or 2 or 3 etc) to store the setting.

Panasonic KX... | Answered on Aug 10, 2020


There are dozens of models and yours is a mystery to us :>)

Google

make model manual

my guess is that yours has been programmed NOT to make outside calls.

Panasonic Lands... | Answered on Aug 02, 2020


Request the diagram directly from Panasonic.

Panasonic Lands... | Answered on Jul 25, 2020

Not finding what you are looking for?
Panasonic Logo

Family Lines

12,411 questions posted

Ask a Question

Usually answered in minutes!

Top Panasonic Lands Phones Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Henk de Ruiter
Henk de Ruiter

Level 2 Expert

80 Answers

Cindy Wells

Level 3 Expert

6164 Answers

Are you a Panasonic Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...