Panasonic Computers & Internet - Page 8 - Recent Questions, Troubleshooting & Support
KV-S3065C has a error F40
You have to replace under the hopper cable part number PJJEC3437Z and board part number PPB747ADF25H from www.part store.com this will take about 2 hours to do because of the covers you have to take off.
10/25/2016 6:22:11 PM •
Panasonic...
•
Answered
on Oct 25, 2016
Touch screen doesnt work on my cf-29
Your Model CF29NWQGZBM the letter "W" indicates that this is a T/S (TouchScreen) Model.
Please verify that the "TouchScreen" is "Enabled" under the BIOS. I recently purchased about a dozen CF29's where there were absolutely NO scratches on the LCD. The reason WHY was because the TouchScreen had been DISABLED at the BIOS level.
I can also share with you another experience I had recently. I purchased approx. 15x CF29 models and every single unit had a defective TouchScreen. When I called Panasonic Canada I was told that since the units were no longer under the three year manufacturer warranty there was nothing they could do about it but that they were aware of this defect and it was a known defect.
I hope this information helps.
Regards from an authorized Panasonic Toughbook Dealer located in Montreal.
The screen on my toughbookcf31 is not working
If you can't even see the "Panasonic" message when the notebook boots up then you should contact manufacturer or notebook provider. These major problems should not be fixed by the user as the guarantee of the notebook can lapse when you open the case.
9/4/2016 11:57:49 AM •
Panasonic...
•
Answered
on Sep 04, 2016
Touch screen dose not work on my CF-30
If your Toughbook has an integrated GPS, this may be conflicting with the touchpad or touchscreen driver. You can fix this by running the GPS Registry Patch - SKIPENUM.REG, which is found in the C:\UTIL\GPS\ folder. This file can also be found by following the link below.If you are using a GPS module that is not integrated, you should contact the manufacturer of the GPS module for a similar patch.If you are not using a GPS module, or if the above steps do not fix your problem, re-install the touchpad and/or touchscreen drivers.
8/16/2016 2:21:58 PM •
Panasonic...
•
Answered
on Aug 16, 2016
I am getting a 14 blink code on my Panasonic TC-P50s30. Do you know what is causing this
Sounds like main digital board fault. 14 blinks denotes that. These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
If blinks continue without any pause, the main board is faulty.
Search the site by type in the "brand name" to your device, in the "Search box at the top right of the display window of the Homepage" to get gathered related posts.
7/14/2016 4:21:37 AM •
Panasonic...
•
Answered
on Jul 14, 2016
4 yr 55" panasonic plasma just died last night
first thing you should try is pull the ac plug out of the wall and hold the on/off button for 20 seconds, then plug the tv back in..this sometimes works bc. the hardware in the tv will reset itself..give it a try..:)
6/2/2016 8:47:57 PM •
Panasonic...
•
Answered
on Jun 02, 2016
Not finding what you are looking for?