Nike Triax - Recent Questions, Troubleshooting & Support


I had the same problem - replaced the battery of my Nike Triax Fury and the time was blinking and none of the buttons were working. Turns out that you need both springs placed in the proper spot - the silver and gold springs. Both springs can be placed in their proper spot with the batter in. The gold one goes in the tiny hole near the "view" spot, and the silver spring goes year the 'cage' that holds the battery in place accross from the gold spring. Good luck.aa07e646-2c11-45e3-b8fa-b40ec2fd82c2.jpg

Nike Wr0139001... | Answered on Jun 05, 2018


mcdevito75 here, Ebay is a great choice for almost any new watch band, or, you can look for a small watch repair shop in your area for this new band.

Nike Triax 0027... | Answered on Mar 19, 2018


Where did you get the band?

Nike Triax Elite... | Answered on Sep 19, 2017


If you have the cheststrap then you don't need anything else. If you don't have the cheststrap piece then you need one. The watch itself does not moniter your heart, It only reads the signal being sent by the moniter on the chest strap.

Nike Triax C5... | Answered on Jun 29, 2017


Any local Jeweler will have this band or one that will work.

Nike Triax... | Answered on Aug 29, 2016


Light button is A
Mode button is B
Start button is C
Reset button is D

Standard Time Adjustment:
1) To set time, date, etc. press button B three times (assuming you start in standard time display mode)
2) Press button D until the area you'd like to change is flashing. (i.e.: minutes, date, day, etc.)
3) Press button C to change. Press once for one unit increment of change. Hold for 3 seconds for speedy advance.
4) Press D again until the next area you'd like to change is flashing.
5) At completion of changes press Button B to resume standard time display mode.

Nike Triax Fly... | Answered on Mar 18, 2015


To change the time you hold the light/set button. It may take some fiddleing but the seconds should blink first. Then you push the lap/reset button to move to a different part you want to change. You push the start/stop button to change the time. Then you push the set/light button to get out of change mode. Hope this helps set-time-vvbd02rb5wmmvmiwlulx4lsd-1-0.jpg

Nike Triax... | Answered on Nov 23, 2014


TRY!

Make sure the watch is facing the correct way. Put the watch on your wrist as you normally would, or pick it up by the strap with your left hand. You should see that the Nike swoosh is right side up. You should be able to read the time.
Find the left side of the watch. This will be your left when the watch is facing you correctly the same way that you would look at it to read the time. You will see at least two buttons. One will be labeled "mode" and the other will be labeled "set."
Press the "mode" button. Press the "mode" button. Continue to press the "mode" button until you have scrolled through the options and are on the correct setting. The correct setting should be "time."
Hold down the "set" button. You should see the currently set time on your watch and the hour should be flashing. You should see a plus sign (+) and a minus sign (-). If your current time says three (for example) and you want to read five, press the button that corresponds with the plus sign. If you want to go backwards, press the button that corresponds to the minus sign. When you are finished hit next.
Change the minutes. Now the minutes should be flashing. Repeat step four: press the button that corresponds with the plus sign to increase the minutes. Press the button that corresponds to the minus sign to decrease the minutes. Hit "next" when you are finished.
Hit "done." Congratulations, you have now successfully set the time on your Nike watch. Now your watch should read the correct time. If you want to get really crazy, you can repeat the steps above to change the date on your Nike watch.

Nike Triax... | Answered on Sep 28, 2014


I had to take the following steps to get it to work in Windows 7 after running the setup executable under the Comments in the Windows row from http://www.ftdichip.com/Drivers/VCP.htm

  1. Open up Device Manager, right click on the Triax Elite and select Update Driver Software.
  2. Select "Browse my computer for driver software" in the window that pops up.
  3. Click "Let me pick from a list of device drivers on my computer."
  4. Scroll all the way down the list of "common hardware types" to USB controller.
  5. Choose FTDI from the list of manufacturers and choose the "USB Serial Converter"
  6. Confirm that you know what you're doing and want to install this driver.
Windows then finds another Unknown Device which is the serial port. Repeat as above but choose Ports for the common hardware types and then FTDI and "USB Serial Port".

Afterwards, run the latest Nike Triax Elite software (that you can download from http://www.nike.com/timing/extranet/elite_software/ and it should work.

Nike Triax Elite... | Answered on Mar 25, 2014

Not finding what you are looking for?

-54 questions posted

Ask a Question

Usually answered in minutes!

Top Nike Watches Experts

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

842 Answers

Anthony Ward
Anthony Ward

Level 2 Expert

397 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Nike Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Nike Watches

  • Forum

View Most Popular

  • Nike Watches
Loading...