New Bright Answered Questions & Fixed Issues

http://newbright.com/wp-content/uploads/2014/06/6689-ws-Manual.pdf

That took me about 10 seconds to find online: http://www.radioshack.com/graphics/uc/rsk/Support/ProductManuals/6000966_PM_EN.pdf

check the battery positioning and the switch.

Harley has one you can buy at any dealer

How do i get the train to turn on and make noises anbd move

Check the connection from the transformer to the track, and that all the track is well connected. Make sure nothing is touching both tracks, shorting them out.

The sensor is a resistive load sensor. The resistance changes as the motor gets hot. Solder the wires back onto the board and whilst keeping the model off of the ground, put it into drive mode. If it doesn't go, then wet your finger and bridge the two solder points on the sensor. Don't worry, you will not get any electric shock as the voltage and current are too low. If it still doesn't drive, then wiggle the motor wiring at the motor. If still nothing, then press lightly on that sensor pcb. There may be a broken track on it. If it is broken, then you cannot solder it. You then need to go to Maplins (if in the UK) and buy a small bottle of pure silver paint. Where the solder points meet the circuit resistive track (it'll be black carbon looking), paint one blob of silver conductive paint onto each of the track beginnings. Let those dry (five minutes) and then try it. It should work. The silver paint will only work if the wet finger trick on the black carbon track works. If no carbon track, then it may be a thermal resistor (thermistor). Replace it. Maplin sells them too, so just buy a few different types (very cheap) and temporarily solder one in place until it works.

gear box is nakerd

I ned battery charger 19.2 V for m'y Hommer 3

You can call the company from where it is made or look on their website on how to purchase replacement parts

Get new battery, I have 4 batteries, all will turn it on, get horn lights, sound. 2 do the exact same thing yours is doing, 1 runs about 5 min then starts into your problem, 1 is good and will run for about 20 mins.

your car needs new motors

Check fuel...then check radiator... Then check spark plug... At last go to service station...

New Bright offers ONLY a 60 day replacement warranty after which there are no parts or service avaialble for this train set.

I would contact New Bright about a replacement or take it back to the store where you bought and select something other than New Bright products.

http://www.newbright.com/

This goes back about 40 years for me. Both Lionel and TYCO had "smokers" in their train sets. My recollection was that the "special smoke oil" was a mixture of very highly refined kerosene and parafin wax. Try a hobby shop such as Hobby Town or some such.

Check the output of the transformer going INTO the controler. Mine is 19VAC. IF the controler is working you should measure 25VDC between the inner and outer track with the controller switched on. If you have the AC but not the DC voltage push the red reset button. Once you have the 25VDC put your train in place (engine and coal car) and it should run.

mcdevito75 here, Contact New Bright online at www.newbright.com for the transformer. Hope this helps. I didn"t see a telephone number at the site. Sorry.

battery with 19.2 volts...same product of the battery u replace

The track layout is simple enough,there are 12 straight peice of tracks and 12 curved tracks. So you can make it one big circle and not use the straight tracks or add 1-6 on each sidewith straight track and you'll have a long oval. Or have 1-4 on each side then add 1-4 after the third curved track of each circlular end to have a big type oval style.Some lites lite up right when you push the power switch on and the remaining lights will work once the train is in motion.

you say you have checked connections and are goodcheck the connections individually remove one car at a time check to see if it works go through the process of eliminating each rail carnarrow it down untill you find the faulty car it might be a fault in just one carhope this helps you