NetGear Recent Questions, Troubleshooting Help & Support

hello, when you say after connecting to AOL 9.0 internet connection is lost, do you mean aol explorer doesn't work, or do you mean IE stops open pages and it was openning before starting AOL? if you close out your AOL does IE then starts working? or tell me what do you have to get it working again?

thank you
Amar Sondhi

Which password do you mean? The wifi passowrd or the admin password?
The admin password is likely to be password (if it hasn't been changed) but the Wifi password you will only be able to see if you can access the router.
Easiest way is to use an ethernet cable between the router and the computer. Open up the netgear admin page (admin & password), then on the left hand side click on Set-up and then select wireless settings. Your wifi password will either be written on the next page or you will see four boxes of numbers with a blue spot against one of them. That one is your passowrd.

Go to the Netgear website and check for the support link, go to that link and look for firmware updates for your model. They install from the computer side of the LAN, you may need to run CAT 5 cable to the inputs to do it.

Try to reset the router. Pull the power plug, wait a few seconds and turn it back in. Most of the time this will help.

https://kb.netgear.com/23517/How-do-I-set-up-my-NETGEAR-WiFi-Range-Extender

the default username/password for this router is admin/1234

netgear vmv 3000 base did you not mean VMB3000? google sees no VMV so.... what are you attempting to connect to what>> a camera is that what it is? maybe as on their web site, the designed to so... https://community.arlo.com/t5/Arlo/how-to-setup-of-vmb3000/td-p/1212018

Manual is here support.netgear.cn/Upfilepath_sc/WN604_UM_14Oct11.pdf Suggest factory reset and reprogram router

To perform a factory reset:

1. Verify that your router's Power light is on.
2. On the back of your router, locate the Restore Factory Settings or Reset button.
3. Use a paper clip or similar object to press and hold the Restore Factory Settings or Reset button for seven seconds.
4. Release the Restore Factory Settings or Reset button. Your router resets.

When you log in to your router again, use the default login credentials:

• User Name: admin
• Password: password

is that a question or stinking sPAM.? I sure can not tell.? this is spam H3LL here, so... try using English.\? how to find? what is xyx? or learn to google, bingo.

Your information is really helpful for me and accurate also. There are so many other information available on net but not correct or half information so appreciate your information. we also share too many information about the router support, <a href="https://www.factonews.com/Netgear-genie-router-tech-support.html">netgear router support</a>, netgear router tech support etc. If you want to read or in a problem to solve issue regarding the router, you can search about factonews.

POPE configuration is logs into your ADSL system and connects to your ISP provider server to link , so one of the reason why it dosent is due to either password and username not correct. Log unto IP address of your Router and go to WAN configuration , Check your username and password and reset to the initial password and username your ISP provider gave you , when you signed up with them. Then apply changes , off your router for 1 min and then power it , then wait for the ADSL light on the router to be stable , connect to the IP address of your router again and "Volla" , it should be fine , if not , contact your ISP provider....

Cordless phones, microwave ovens and wireless surveillance cameras between the modem and the device will do it. If it's hard wired to the computer, the signal strength from the phone company may be low. Call the phone company to have them come out and test the signal level that is applied to the modem.

Here are some troubleshooting steps that I suggest you try:

1. Check physical connections.

a. Connect the modem to the Internet port of the router. The Internet “i” LED on the front of the router should light up.
b. Connect the computer to one of the four LAN ports (i.e port 1, 2, 3 or 4) on the back of the router. The corresponding port light where you connected the computer should be lit up.

2. Access the router's web-based utility.

a. Please open any web browser like Internet Explorer or Netscape Navigator.
b. Connect to the router by typing http://routerlogin.com/basicsetting.htm or http://192.168.1.1 in the address field and click Enter or Return key.
c. A window will prompt for a user name and password. By default, the user name is "admin" and the password is "password".

Note: If you were unable to access the router's web-based utility, you may reset the router to restore the settings to factory default.

To reset the router:

a. Please push the reset button at the back of the router and release after 30 seconds.
b. Unplug the power adapter for 10 seconds and then plug it back in.

3. Configure the router.

If your Internet Service Provider is using a cable connection, please follow the steps below:

a. Click on Basic Settings under Setup tab.
b. Select No for Does Your Internet Connection Require A Login?.
c. Scroll down on the center page and look for the Router MAC Address section. Set it to Use computer MAC address and click on the Apply button.

If your Internet Service Provider is using a DSL connection, please follow the steps below:

a. Click on Basic Settings.
b. Select Yes for Does Your Internet Connection Require A Login?.
c. Select Other on the Internet Service Provider drop down box.
d. Enter your ISP's username (username@ISPdomain) and password. Then, click on Apply.

4. Configure the wireless settings.

a. Click on the Wireless Settings under Setup.
b. Change the SSID to any unique name.
c. Scroll down, look for the Security Options settings and select WEP (Wired Equivalent Privacy).
d. Set the Authentication type to "Automatic" and the Encryption Strength to "64bit".
e. Leave the Passphrase field blank, select Key 1 and enter a 10-digit number.

Note: The 10-digit number you typed in the key 1 will be the password or network key for the wireless connection.

f. Click Apply button to save the changes.
g. Go to Router Status under Maintenance tab and check if there is an IP address under Internet port. If it's 0.0.0.0, do a power cycle.

5. Power cycle.

a. Power off the modem, router and computers.
b. Turn on the power of the modem first and wait for it to initialize, the lights to stop blinking.
c. Power back the router and the computers. Check if it will be able to get online.

If you have wireless computers, you can connect them wireless to the router. Kindly follow the instructions below:

6. Connect wireless computer to the router.

If you are using Windows XP with Service Pack 1, please follow the steps below:

a. Please right click on the Wireless icon on the right lower end portion of your computer.
b. Then click on View Available Wireless Networks.
c. Click on the Advanced tab.
d. Please delete all the preferred networks then click on OK.
e. Right click on the Wireless icon again and click on View Available Wireless Network. Please select your network and click on Connect. It will ask you for the network key.
f. Please type in the network key and then confirm it. Network key is the password you type on the key 1 of the wireless settings of the router.
g. Make sure not to enable IEEE and then click on Connect.

If you are using Windows XP with Service Pack 2, please follow the steps below:

a. Please right click on the Wireless icon on the right lower end portion of your computer.
b. Then click on View Available Wireless Networks.
c. Click on the Change Advanced Settings.
d. Click on the Wireless Networks tab remove all the preferred networks then click on OK.
e. Right click on the Wireless icon then click on View Available Wireless Networks.
f. Select your network and click on Connect.
g. It will ask you for the network key. Type in the network key and confirm it. Then click on Connect. Network key is the password you type on the key 1 of the wireless settings of the router.

If you are using Windows Vista, please follow the steps below:

a. Click Start then select Connect To.
b. Connect to a network window will show up.
c. Select your wireless network and click Connect.
d. It will ask you for a network key. Type in the network key and confirm it. Then click on Connect.

From the above configuration, please check if you can now access the Internet.

You can order an adapter that plugs into the wall socket at the router and at the computer. The direct connect to the router and the network adapter in the computer assures a good connection. Of course, a laptop that you move around with couldn't use this as effectively. https://www.cnet.com/news/top-five-power-line-adapters-when-wi-fi-fails-you/

Are you trying to use MAC filtering. You would just need the MAC from the network setup screen and add it to your router/firewall. If you are using a Mac (Apple) computer you would, providing you have a wireless adapter connected to Mac, just go into "System Preferences" and use the wizard under "Print & Scan". Make sure the networking on the printer is in on the same as your Mac.

http://www.downloads.netgear.com/files/GDC/WGR614V7/wgr614v7_setup_manual_21apr06.pdf hope this helps, but I doubt it will be compatible with new standards

110/220v will be the input voltage on the adapter. You need to check the required voltage required by the extender which will be somewhere in the 5 to 12v range and compare that to the output of the adapter.

These figures will be displayed on the labels for each.

It is also sensible to check that the amperage required by the extender can be supplied by the adapter. If the adapter is higher it will be fine but if it is lower you risk burning out the adapter.