Necchi Sewing Machines - Popular Questions, Answers, Tips & Manuals

Instructions normally come via the manual, but you might find a sewing club. https://www.google.com/search?q=Necchi+4825+manual https://www.google.com/search?q=Necchi+sewing+club+near+me ..

They will only go in one way, they have to be correctly orientated. https://www.google.com/search?q=Necchi+model+3355+replace+bobbin+case ..

Question edited for clarity. Question moved to Necchi category. This appears to be a tricky machine..... By this time most manuals were generic like that without a name on them, there were so many badged identical machines that a separate printing for each name was out of the question. So many machines didn't even get a badge until they reached their destination country. No manuals for it. Set a watch for it on eBay. There are similar Necchi. https://www.google.com/search?q=Necchi+Alco+1300SU+manual https://necchi-usa.com/pages/support ....

Question edited for clarity and all the typos. Question moved from Televisions to make model category. The whirling noise is the motor. It may be that the drive belt has broken? When was the last time it was professionally cleaned, serviced and timed? With moderate use, they need doing every 2 to 3 years. The inside workings of sewing machines are very tough and seldom 'break'. https://az589519.vo.msecnd.net/productdocuments/Inst-book-NECCHI-FA16.pdf Parts including the $4.99 drive belt https://www.sewingpartsonline.com/necchi-4575-sewing-machine-parts.aspx?index=32 Generic videos on Necchi belts

Is this machine new to you or have you had it awhile and it worked fine before?Are you sure it is top thread?... use a similar but contrasting color for top thread to be sure.Do you have the manual to be sure you are threading it properly?See following video on threading the Lydia 3.https://youtu.be/wVifJVsrO80Comment below for further assistance.

Fix in what way? What is wrong with it?

take it back to the place where you took it two weeks ago. Otherwise, need more info...where in the machine did it wrap?

If the needle positioning dial is not working on a new out-of-the-box Necchi Q132A sewing machine, it could be a manufacturing defect or a loose connection. Here are some steps to troubleshoot the issue:

1. Check the manual: Make sure you are following the correct steps to use the needle positioning dial. Refer to the manual and double-check if you are using the dial correctly.
2. Check the connections: Open up the machine and check if all the cables are securely connected. If any of the wires are loose, reattach them carefully.
3. Contact the manufacturer: If the above steps do not solve the issue, contact the manufacturer or the seller from whom you purchased the machine. Since the machine is new, it should be under warranty, and they should be able to provide you with the necessary support or even a replacement if needed.
4. Take it to a repair shop: If the machine is out of warranty, or you prefer not to deal with the manufacturer, take the machine to a reputable sewing machine repair shop. They will have the expertise to diagnose and fix the issue.

Remember not to attempt any repairs yourself as it could void the warranty or cause further damage to the machine.

It sounds like there may be an issue with the needle clamp on your Necchi NC204D sewing machine. The fact that the needle falls out when you try to tighten it suggests that the clamp may not be holding the needle securely. Here are a few steps you can try to fix the problem:

1. Check the needle clamp: Make sure that the needle clamp is tightened properly and that the screw is secure. Also, make sure that the needle is inserted all the way into the clamp.
2. Check the needle: Make sure that you are using the correct type and size of needle for your machine. The needles that came with the machine should be the correct size, but it's good to double-check.
3. Check the needle plate: Make sure that the needle plate is clean and free of any debris or burrs that could prevent the needle from seating properly.
4. Check the needle alignment: Make sure that the needle is aligned properly and that the flat side of the needle is facing the back of the machine.
5. If the problem persists, it's best to contact Necchi customer service or a professional sewing machine technician for further assistance.

It's important to note that working with a sewing machine can be dangerous, if you're not comfortable working with it, it's best to get it serviced by a professional.

if your machine has this slide button on the motor casing maybe you need to switch it back and forth a couple of times

The foot pedal needs cleaning inside, or it needs replacing.

No free ones. $15 in the first link. https://www.google.com/search?q=necchi+4575+manual ..

Hi, Please add a bit of some olive oil (or similar oil) to shafts and areas of your machine that facilitate the selector's movement. This should lower friction and allow for movement. Thank you.

You use a Rolled Hem Foot. See videos and spares details. https://www.google.com/search?q=necchi+pl1036+rolled+hemming ..

Have you tried Nacchi ... https://necchi.uk/product-category/necchi-spare-parts

The is usually an adjustment to tighten the belts by moving the motor. There are other ideas here, clutch, the knob in the handwheel or the screw in the needle bar.. https://www.google.com/search?q=Have+a+Necchi+534FB.+The+hand+wheel+does+not+turn+the+needle+bar%2C+belts+are+loose ..

Only from the maker by the looks of it. https://necchi-usa.com/search?q=walking+foot Not available from the normal outlets. One on Amazon but not for your machine. https://www.google.com/search?q=necchi+6018+walking+foot ..

If you haven't removed the top to clean and oil the cams then likely they are stuck, hence zigzag.

Manual in Italian (Google translate helps): https://manuall.it/necchi-519-macchina-per-cucire/ After the machine has been wiped clean with a rag, apply a drop of good oil to every movable part; to the bearings of the lower shaft (to which the shuttle carrier is attached) and to all other shaft bearings of the machine. The various oil holes in the machine indicate where the oil must be applied. Sewing machine oil is a white mineral oil, meaning it is clear and has no smell. The oil has a light viscosity and will not collect on the machine's gears.