NEC Audio Players & Recorders - Popular Questions, Answers, Tips & Manuals

0helpful
1answer

I am trying to connect a NEC t-710 tuner to a NEC Av350E AMP - how do I do that?

A tuner would typically have an output labelled "line out" or similar and the amplifier would usually have either a "line in" socket or a dedicated tuner input and it is a matter of connecting the two with a suitable lead.
2/7/2019 12:17:21 AM • NEC Audio... • 56 views • 1 helpful votes
0helpful
1answer

NEC VH-605 VCR - Very Snowy Picture

Video head needs thorough cleaning. If no head cleaner, then run a few long tapes through it in the fast scan mode since the tape itself is abrasive and will over time remove debris from the heads. If that does not do it, try a chemical cleaner to dissolve the material.
9/1/2017 11:39:02 AM • NEC Audio... • 120 views • 0 helpful votes
0helpful
1answer

Wanting to extend ring time - changed by itself - only ringing 5-6 times before going to message bank.

5-6 rings I think that is the best you can get link to a manual for it SV8100 DT310/DT330/DT710/DT730 User Guide - NEC Corporation ...https://www.necam.com/Docs/?id=5601ae16-b7e2-4e8c-a769...NEC-10645 UNIVERGE SV8300 DT300 DT700 USER GUIDEau.nec.com/.../SV8300_Handset_Manual-ce03fb6c-32af-4991-9bd5-8ec.
9/9/2016 5:16:32 AM • NEC Dtl-12d... • 520 views • 0 helpful votes
0helpful
1answer

HOW DO I CORRECT THE DISPLAY OF MY PROJECTOR NEC P420X SHOWING VERTICAL LINES AND BLUR DISPLAY?

time to change bulb perhaps
8/29/2016 5:07:27 PM • NEC NP-P420X LCD... • 179 views • 0 helpful votes
0helpful
2answers

NEC V260XG temperature error

The most common cause is dust inside the projector that leads to overheating & auto shutdown. If you have an air compressor you can use the blow tip accessory to blow as much dust out as you can without taking apart the projector. You may get by using a can of compressed air available at Walmart, etc. electronics section. Concentrate on vented areas & where you can see or hear any fans. Do this outside so it doesn't make a mess. If you know how to take out the lamp there's usually close access to the main cooling fan through the lamp compartment, blow air through there & it will follow the right path to exit correctly without blowing dust all over the inside.
4/12/2016 4:38:17 PM • NEC Display... • 379 views • 1 helpful votes
0helpful
1answer

NEC V260XG temperature error. How to Stop??

check the thermostat; it appears that either the thermostat is not working properly, or is not set right or damaged
4/23/2016 3:53:05 PM • NEC Display... • 184 views • 0 helpful votes
0helpful
1answer

Nec v260xg image alignment problem

Try the Keystone correction function to correct the trapezoid distortion. 26182914-h3gmruk4y5pvvzbyocke3n3a-1-0.jpg
5/2/2016 7:29:42 PM • NEC Display... • 124 views • 0 helpful votes
0helpful
1answer

Whin i plug vga cable screen flickering

Hi Prakash Clean Connector Pins with spray Wiggle to see if bad connection Check for Female socket loos worn holes in connector pin
9/12/2015 12:36:51 PM • NEC NP-M260X LCD... • 158 views • 0 helpful votes
0helpful
1answer

NEC DT300 has call light flashing red with no call on the line. How do I make it stop?

PUSH JUST THE BUTTON SPEAKER TWICE IT MAKES THE HAND FREE CALL YOUR PHONE WAS FORGOTTEN ON FREE HANDS CALL
10/20/2014 11:47:42 PM • NEC Univerge... • 2,009 views • 0 helpful votes
0helpful
1answer

How do i reset my lamp timer on my nec v260

go to menue / reset/clear lamp hours, all the buttons needed are on the box, push menu & with the cross navigate & with enter confirm selection, exit gets you back at any time, on the nec/support website you can get the np-v series manual good luck
10/30/2014 1:10:51 PM • NEC Display... • 1,204 views • 0 helpful votes
0helpful
1answer

Why has the phone reversed, dial tone works only when phone is hung up why?

If I understand you correctly, when you leave the handset in the cradle and press a line, you can hear the dial tone. But, if you lift the handset and then select a line you don't hear anything through the headset. If this is correct, I suspect the handset is damaged, the cord is damaged, or if you're lucky, the clips may not be plugged all the way in on both sides. If you have another phone that is the same, you can switch handsets to test this theory.
10/19/2014 7:03:41 PM • NEC 22b Hf... • 111 views • 1 helpful votes
0helpful
1answer

Change the bulb on NCE v260X and I still have white snow flake when I turn it on

Have you adjusted the contrast and Keystone. A new bulb should be plenty bright. Maybe clean the lens. There is in some types of Projectors a color wheel inside this can become dusty. But not often if you keep the filters in place and clean them. This could cause a snowy picture as well. Hard to say without actually seeing the picture to say what the issue could be. But these are some of the stronger possiabilities.
9/30/2014 8:46:49 PM • NEC NP-V260 DLP... • 79 views • 0 helpful votes
0helpful
1answer

Line three comes up busy and says vacant number

There is either no outside line connected to that port on the switch or you do not have access to that line.
3/31/2014 1:09:01 PM • NEC Dx7na 12txh... • 90 views • 0 helpful votes
0helpful
1answer

Why is my display is flashing "BATTERY LOW" where is the battery located?

Look on the bottom for a door to access the batteries. If all else fails go to the manual you received with the phone and follow its instructions.
4/28/2014 3:33:20 PM • NEC Electra... • 32 views • 0 helpful votes
0helpful
1answer

MSG on Display

Once the messeges are cleared, the light will stop blinking.There should be a button to push, which will allow you to access the messeges options.
6/28/2013 1:52:33 PM • NEC Univerge... • 412 views • 0 helpful votes
0helpful
1answer

Program headset in to NEC DT300 phone

how do i connect head set in nec dt 300 series phone ? and is there any configuration needed for that ?
3/27/2013 8:41:28 PM • NEC Univerge... • 1,346 views • 0 helpful votes
0helpful
1answer

How do I change the time on my phone

Depending on the phone there will be setup to enable the setting of the timeand date, this can be set to sync with the phone system to auto keep track of the time. You can set up other location times as well. Look for an instruction manual on your phone, on the web via google
1/13/2013 2:42:25 AM • NEC Dx2na... • 108 views • 0 helpful votes
0helpful
1answer

My phone is not ringing? I can see the red light blinking though.

Please check the volume settings or switch, it may be set on mute.
8/28/2012 5:56:38 AM • NEC Dterm Series... • 183 views • 0 helpful votes
0helpful
1answer

How to change the display name

Consult the owner manual or if do not have Google the model number for manual. That info has to be in the owner manual--last resort call the customer service for the unit.
8/28/2012 5:11:47 PM • NEC Electra... • 95 views • 0 helpful votes
0helpful
1answer

How to ping an nec phone system from an ip phone

Try disabling/enabling the SIP helper. (this change requires a reboot I think because it changes the kernel modules)www.businesstelephonesystem.org/
6/21/2012 10:19:46 PM • NEC... • 601 views • 0 helpful votes
Not finding what you are looking for?
NEC Logo

84 questions posted

Ask a Question

Usually answered in minutes!

Top NEC Audio Players & Recorders Experts

Ekse

Level 3 Expert

13435 Answers

 Grubhead
Grubhead

Level 3 Expert

5720 Answers

The Knight
The Knight

Level 3 Expert

76703 Answers

Are you a NEC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...