Mercedes-Benz Logo

Mercedes-Benz Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 947 Products
  • 92K Answers

It sounds like you have a vacuum leak somewhere between your valve and your source. A common vac leak that occurs on the 220 is at the vac. rubber y located at the back of the intake manifold. Follow your vac. line from the egr to the switchover valve and from the switch over valve to the source. Which is probably the y connecter

1998... | Answered on Jul 02, 2020

I am assuming that the engine won't even turn over. could be lots of different things. The simplist is to make sure the car in in PARK , won't start if not. Other things could be , Security imobilizer if you have one. Does your key have a electronic chip in it ? Try your other set of keys if you have one. Check if battery connections are clean and tight.

2003... | Answered on Jun 19, 2020

under the thermostat housing. you have to remove the belt with a crow bar take out all the nuts and screws remove the pump clean the area put new gasket and put the new pump back . than the belt will take a while

1993... | Answered on May 30, 2020

Since this module must be programmed for your car you will need the dealer to do this.

Mercedes-Benz... | Answered on May 08, 2020


Mercedes-Benz... | Answered on May 08, 2020

Hi Reg Cristie! Look at the
- there are plenty descriptions of DTC (diagnostic trouble codes or fault codes) for MB Actros. Have fun)))

Mercedes-Benz... | Answered on Apr 25, 2020

How can i get a manual or a cd of actrors/axor that has fault codes and wiring diagram.pls help

Mercedes-Benz... | Answered on Apr 04, 2020

Go to your owners manual to find the answer if you don't get one here.

Mercedes-Benz... | Answered on Apr 04, 2020

i believe its an air supply issue to transmission, either actuator on trans or the air drier,

Mercedes-Benz... | Answered on Apr 04, 2020

i also have the same problem, i have also changed the screen i have two and both flash ten times?

2008... | Answered on Mar 21, 2020

You can find the oil life reset procedure here

2008... | Answered on Mar 20, 2020

Je recherche le code de la radio Mercedes Benz audio 10 cd A 1708200389 Model n° MF 2910 Fabriqué en France S/NO AL 2910 1 0429494 B

1999... | Answered on Mar 05, 2020

You have to pull the inside door panel to get to it then there are 2 electrical connectors, connecting the wires to the switch(be careful to use needle nose pliers and grab the connector and not the wire) remove wires from switch, replace switch, replace wires on new switch(as long as there is only 1 wire on each side of switch don't worry about polarity), and replace inside door panel. To test new swich turn ignition on and actuate switch on inside door panel.

2006... | Answered on Mar 02, 2020

Can you please re-ask this questions?

First, you said the button Unlocks the Car and then say it Won't?
Second, The lock/unlock does not control the Courtesy lights, there is a Time delay but now here is the kicker....

Does the Courtesy lights come on when you use the FOB ?

If they do, they you have a problem with the Button or the Button Controller or a wire.

Third, I am not sure what Button you are talking about on the REAR HEAD RESTRAINTS? Are you talking Head Rests? I have never heard of as HEAD RESTRAINT

2000... | Answered on Feb 28, 2020

The hood release is a red lever under the dashboard about shin height. I found the image on a Haynes online manual -
Opening the bonnet Mercedes Benz Class 2008 2011 Petrol B180 1 7

Mercedes-Benz... | Answered on Jan 25, 2020

On center console knob select vehicle settings
click on that then choose time and date and select your actual time and date

Mercedes-Benz... | Answered on Jan 22, 2020

Solution #1 is not correct.. reason, why engine does not start when those codes are shown, is pump control unit (PCU), or electromagnetic valve. You should give PCU to fix (mostly it's broken transistor inside) or to change you current PCU to the new (need to be programed) or buy whole new VP44 PSG5 pump.
Sorry for my broken language :)

1994... | Answered on Jan 10, 2020

hi,i have no doubt for there diagnose because they read on star diagnose,hoping that they read the actual values,you mention the fault is coming when you turning,maybe the steering angle sensor, if not mistaking,they have a sti,stated poor contact in wiring connection on control module

2001... | Answered on Jan 10, 2020

Hi, if its the complete seat check the runners beneath seat maybe sumtin in 1 of ridges, or if its the back of seat shake/rattle back and forth while holding button you know d sayig reoair by trial or error. Good luck

2002... | Answered on Jan 06, 2020

Pull fuse until u figure out problem

2000... | Answered on Jan 03, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

john h

Level 3 Expert

23424 Answers

Brad Brown

Level 3 Expert

18402 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides