Hi,
Please try clearing sequences by rotating the cycle dial counter-clockwise a bit before starting a new cycle. The reset should then allow your newly chosen cycle to work.
Thank you.
The circulating fan(Freezer Fan) supplies air to freezer as well as the refrigerator. As the DC brushless motor wares out the rpms reduce to a point that it is hard to diagnose. This motor alone costs around $80.00(appliancesfactoryparts.com) Replacement of the fan motor is labor intensive to remove fan assembly because the electrical connections are at the exteme rear of the freezer compartment
When your freezer is displaying an SH error code on the temperature display screen, it means that the freezer temperature sensor has shorted out. To troubleshoot this problem, you will need to start by disconnecting your refrigerator from its power source and locating the freezer temperature sensor.
Sept 6, 2022
Hi,
the error relates to a motorspeed sensing error. I would advise you to get the washer serviced via maytag since there are multiple portions breaking down. You can call Maytag to get this done and learn about the actuators potential links to the machine's issues: 1 (800) 344-1274
Thank you.
Hi,
you might reach out to a third party dryer manufacturer and ask them if they can provide the part that you're looking for. You might start by looking through white pages or calling 411 to find such a company. Thank you.
The electronic control panel and board has detected a runaway in the temperature and the control board and the heating sensor could be broken on your dryer and need to be replaced.Or the circuit breakers may need replacement then.
The plastic spines on the hub plate that connects the tub to the transmission is stripped and slipping.Order a new plastic hub plate.Remove the center cap of the wash plate agitator located on the bottom of the tub.Remove the 11 mm (7/16" bolt) with an impact tool (a must).This will save you a day's worth of pain and grief and worth the $70.00. Spray sometimes rusty metal spline with penetrating oil.screw bolt back on and leave about one full turn loose.Replace cap and run a load of wash.This will break away the rusty spline connection that holds the agitator wash plate on to the transmission.Most any other way tugging on the plastic agitator wash plate will break it (new one for $170).repeat steps above removing the center cap and bolt.Now the round agitator wash plate should wiggle off easy.your will see the plastic hub after removal of the agitator wash plate.Pull out the plastic clamp and unscrew the 6 screws.clean the transmission spline shaft with a metal brush spraying it with penetrating oil.clean and replace the hub plate with new hub plate.rebuild the washer with the same steps as you used to diss-assemble it.You fought the washing machine and you won!Pat yourself on the back!
You will have to call a person that repairs major appliances to have a look and see what the problem is. There could be something wrong with your washing machines controls for the door not to open at all. Or the door latch could be the problem and the motor.
(I'm providing a late, modern response for people like me who land here in 2022+)
I had the same problem. Gradually it got worse until only Bake ' Cancel work. Sometimes the problem is due to bad ribbon cable connections; sadly, with this oven, the issue is the membrane buttons having failed. It's frustrating, because this has happened with every version of this model that I have seen. Add to this that the membrane buttons are behind a sealed panel that you can't access without breaking it, and you'll quickly learn that you need to buy the replacement part. 5765M483-60 is the matching control unit, but make sure with the vendor that it is the right size for your unit first; it's expensive. It's also now out of stock and is a 2-3 month special order at most vendors. The replacement is tedious, but simple and approachable for a first time DIY'er. At this point, I'd rather buy a new replacement oven instead, but finding 27" models is difficult as most are 30" now, which won't fit my cabinetry - thus I bit the bullet and bought the replacement control unit. Oven came with the house on purchase; former owner told me she had already done the same repair once before; so that means this problem will keep recurring.
