Maytag Logo

Maytag Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 2K Products
  • 163K Answers
  • 3M Views

the oven that wont work see if ignitor glows at pre heat if not and voltage to it replace ignitor

Maytag Ovens | Answered on Jan 18, 2020 | 42 views


If there is a LOCK button hold it down for 15 seconds

Maytag Washing... | Answered on Jan 16, 2020 | 37 views


POSSIBLY THE DOOR SWITCH SHIFTED

Maytag Washing... | Answered on Jan 14, 2020 | 23 views


Most likely a bad main board. If you have the model info, i could possible over more details, thanks

Maytag Washing... | Answered on Jan 12, 2020 | 25 views


call maytag repairman

Maytag Washing... | Answered on Jan 08, 2020 | 35 views


F04 E04 means low power voltage to dryer - check both sides of AC receptacle for 110 to 120VAC on each side to ground - check breaker panel for tripped or bad 220VAC breaker. Only one side may be suppling voltage to dryer.

Maytag Washing... | Answered on Jan 08, 2020 | 24 views


i don't know. most dryers come with a chart showing what wires are for. green is usually used for ground but read
your chart. few have chart with owner's manual and most i have seen are in a clear plastic bag stuck on the back or
stuck in the open area under the tub.

Maytag Dryers | Answered on Jan 07, 2020 | 56 views


May be a water pressure sensor problem.
This tells it when the tub is full.
start with this video
https://www.youtube.com/watch?v=2pIVkAxWSXg

Maytag EPIC... | Answered on Jan 03, 2020 | 2,292 views


Well I just changed the capacitor on my washer. It would fill with water and stop. My first thought was lid switch it checked out good. Next timer but usually if you switch to another type wash cycle it did not work so I thought timer must be good. I tried to get it to pump out so I pulled pump off shaft and it turned free( I have direct drive to pump no belt) Two metal band clip on to hold pump and motor shaft turned free. I then checked capacitor it would not charge and was not storing charge. The capacitor can shock you very bad do not touch metal connectors till you discharge stored voltage. I dropped water level by just putting end of drain hose in five gallon bucket I had to dump several buckets. I ended emptying by scoping water out with big plastic cup into bucket. I have no bottom on my Maytag so I just leaned it against the wall to get to pump and capacitor. A couple times when I tried to start with washer full of water, I would hear a buzz sound at bottom but not every time. Washer has been working great for 2 weeks now. Make sure to unplug washer before working on it.

Maytag Washing... | Answered on Jan 01, 2020 | 43 views


Nothing happens when push start button.
All limits are good.
Element tests at .001 ohms.

Maytag Dryers | Answered on Jan 01, 2020 | 1,513 views


When door locks like that next time. If you remove the top of the machine. Reach down inside on left side. There is a small wire cable that you pull up on. Will manually unlock the door. Then plug power cord in to wall. Power it on let it go through reset cycle and it will work properly again. However if you can't reach the latch through the top. Tilt washer forward and reach up from the bottom. If you get an F1 code it's low water pressure.

Maytag Neptune... | Answered on Dec 31, 2019 | 916 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Maytag Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Brad Brown

Level 3 Expert

18154 Answers

Cindy Wells

Level 3 Expert

6065 Answers

Are you a Maytag Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...