Maytag Heating & Cooling - Answered Questions & Fixed Issues

If name tag is legible, check there. Guess 134a

Maytag Heating &... • Answered on Jul 20, 2019 • 66 views

Window AC units need to be leveled horizontally and slightly tilt back for proper drain purposes.

Maytag Heating &... • Answered on Jul 27, 2018 • 82 views

AC units don't need water, only evaporative coolers do.

Maytag Heating &... • Answered on Jul 19, 2018 • 250 views

Siphon it out with a hose.

Maytag Heating &... • Answered on Jul 19, 2018 • 168 views

What make of unit you have. You can get most parts at United refrigeration .fw webb does York, johnston supply does goodman and dcne does Carrier. Also can get replacement parts at grainger

Maytag M6P09S2B... • Answered on Feb 26, 2018 • 113 views

Could the on/off switch be shorted? Could check with a volt/ohm meter, or remove and replace.

Maytag M6Y12F2A... • Answered on Dec 29, 2017 • 76 views I couldn't find the instal instructions , but this info should help with the sizing.

Maytag M6Q10F2A... • Answered on Dec 27, 2017 • 575 views

sounds like the contactor is welded closed. make and model helps but with limited experience you may want professional help. Best Wishes!! If you need further help, reach me via phone at

Maytag M7Y10F2A... • Answered on Nov 25, 2017 • 64 views

It sounds like you have a leak and the Freon is gone.

Maytag M6X08F2A... • Answered on Oct 21, 2017 • 138 views

The letters BTU means British Thermal Units.

Maytag M7X05F2B... • Answered on Sep 30, 2017 • 44 views

I think the M6 is the sixth month and 06 is 2006 That is what I was told.

Maytag M6X06F2A... • Answered on Sep 30, 2017 • 236 views

The switch or knob for that burner is shot. to disconnect that burner first see if there is a fuse that goes to just that burner and take it out. That should stop any power to that burner. If not take the knob out and undo the wires to that switch and put electrical mar rets on the wire ends. Just as a precaution put electrical black tape on the outside of the mar rets to make sure they do not come off. DO NOT try to put these wires back on the switch.

Maytag Heating &... • Answered on Sep 30, 2017 • 54 views

yes filter prevents coils from getting dirty which will then cause issues best to have a filter

Maytag M6X05F2B... • Answered on Sep 20, 2017 • 45 views

Possibly dead batteries in the tstat. Turn power off, remove tstat , wire red yellow green together and turn unit on. This should make everything work, if it does the problem is the tstat. If you need further help, reach me via phone at

Maytag M6Y18F7A... • Answered on Jun 30, 2017 • 55 views

Check vibration eliminators on the feet of the compressors, over time of running in tough conditions they wear out and cause rattling. If this does not fix the problem see below -check amp draw, if amp draw is high windings are wearing out and compressor is running harder, may need replaced - check to make sure your refrigerant charge is correct you could be slugging the compressor -find other ways to isolate compressor operations

Maytag... • Answered on May 29, 2017 • 79 views

Make sure the Thermostat is set correctly! The problem with mine was the temp in the house was colder than my A/C lowest thermostat setting.I had my AC temp setting on 66 degrees.The temp in the house was a little lower so the AC didnt kick on just the fan blowing cool air and no compressor working. The next day it was warmer out and the house temp was 79. So when I powered up the AC set at 66 i heard the compressor kick in and the AC worked fine.

Maytag M6X06F2A... • Answered on Apr 29, 2017 • 100 views

Not finding what you are looking for?
Maytag Logo

Ask a Question

Usually answered in minutes!

Top Maytag Heating & Cooling Experts


Level 3 Expert

3063 Answers

Cindy Wells

Level 3 Expert

6278 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Maytag Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides