Manitowoc Heating & Cooling - Recent Questions, Troubleshooting & Support

Water restricted somewhere. So 1st filter; 2nd water inlet valve. You need to deep clean this machines every 3 month.

is the evaporator getting cold? does it sound like the compressor is on?

What make and model of ice maker do you have? Is the unit making ice? If so, about how much? Most commercial bin type ice makers are not engineered to maintain the ice once it drops into the bin. Older ice is intended to melt and the water should drain out of the bin as new ice is deposited on top. It may be that you are consuming ice at a rate greater than the unit is designed to produce ice, or that the unit is not set to the highest ice production rate (if adjustable). Alternatively, if the inside of the bin is hot (warm) you may have another problem with the unit (e.g., gasket leak). Was the unit previously working? If so, are you aware of any events that took place just prior to the change? Some units have a defrost or a cleaning mode, which will actually generate heat inside the unit. Make sure the unit is set to the correct mode.

that is a 400 lb. per 24 hours machine. can you explain the problem in further detail.

the resistance of your compressor ok. can you test it blk. blu red terminal to the body of compressor if there is a continuity if have your compressor is grounded one testprod to blk.blu.and red and one test prod to the body of comp same as on your fan motor maybe it is grounded or burn out.test the continuity. also maybe your breaker is defective try to check or your compressor maybe stock up cause of tripping of breaker or your breaker under rating to your unit check it.

one of the plate/s is/are loose on the condenser and the ice is freezing behind the plate and is not releasing during the harvest cycle. Solution with a rubber mallet knock the plate/s back or if loose enough pull out completely, you will just have longer cubes of ice. Hope this helps Tim

Water valve is the only thing I can think of with the water level switch already being replaced. The water valve must not be cutting off completely, allowing water to continue flowing. They get trash in them and the diaphragm get weak.

Question edited for clarity, full 'make model (what it is)'. Email address removed. You don't need the site's 12 million annual viewers emailing you to say they can fix it for a thousand bucks! Finally, Please don't type in all CAPS, it is considered SHOUTING and is harder to read. Repair Clinic has some good ideas, but your model is discontinued

Fedders Air conditioner won't turn off

Repair Clinic https://www.repairclinic.com > RepairHelp > Fedders-Ai... Here are the most common reasons your Fedders AC compressor won't turn off - and the parts & instructions to fix the problem yourself.

Why Your Air Conditioner Isn't Shutting Off, and How to Fix It

Williams Comfort Air https://williamscomfortair.com > ac-wont-shut-off When your air conditioner won't shut off, it's natural to worry about wasting electrical power as temperatures become too cool for comfort. ..

Here are the steps you might want to follow: Setting the Draining Cycle Times (Dump Interval): This setting controls how often the unit dumps the water. You can adjust this setting to reduce the frequency of water dumping. Setting the Drain off Delay Time (Dump Delay): This setting controls the delay time before the unit starts to dump the water after it has been turned off. If adjusting these settings doesn't work, there could be other issues with your unit. For example, a continuous water dumping problem could be due to a faulty dump valve or a problem with the float valve.

Frego split ac error code h3 what is problem

Model 2320cpb. E2 code

Blue star inverter Ac HP error shown on display

Why do you need to dismantle this? Some of these types of cooler do not have replaceable parts inside. They are usually classed as a "Throw away" machine. It is often easier and cheaper to replace it than repair it.

Azure 1.5 ton splits ac old model e2 error

Blocked jets clogged with dust or dirt, blocked injector need a clean / service

o reset your Homebasix Oscillating Parabolic Heater, follow these steps: Unplug the heater from the power source. Locate the Manual Reset Button on the heater. It's usually a small button or switch. Use a fireproof, non-conductive rod (such as a wooden stick or plastic tool) to press the Manual Reset Button. After resetting, plug the heater back in and check if it functions properly. Remember to ensure that there are no flammable objects within 3 feet of the heater and that it is placed on a stable surface.

Voltas arrear code 88

https://www.fix.com/repair/appliance/air-conditioner/does-not-turn-on/