Malber Washing Machines - Recent Questions, Troubleshooting & Support

How to replace door switch in malber 1000

Same as Whirlpool or Kenmore. See the videos.

https://www.google.com/search?safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk01XDAPLu6ilD-Vv2EosadhBB6Z1Bg%3A1614043430220&ei=Jlk0YN3oDOmt5NoPj_-hsAw&q=whirlpool+front+load++washer+replace+door+switch

..

Malber Washing... | Answered on Feb 23, 2021

2 Answers

Model WD1000. Why is wash cycle interrupted periodically?

The simple answer is to fault the cycle timer but some action controlled by the cycle timer, such as pump operation, may not be available at the time called for.

Malber Washing... | Answered on Jan 04, 2021

1 Answer

Model WD1000. What causes it to shut down intermittently?

THEN CALL A LOCAL REPAIR SERVICE TO FIGURE OUT IF THE BOTTON NEEDS REPLACED ,

Malber Washing... | Answered on Nov 18, 2020

3 Answers

Went through a cycle of laundry but did not empty the water. Removed laundry and ran the drain cycle. Did not drain. Added a new small load of towels.

1. Defective pump
2. Defective cycle timer

Malber WD1000... | Answered on Nov 11, 2020

1 Answer

Need service for Malber 1000 heating element..

Hi. Mike here. I repair Malbers in the Washington D.C. area. The most likely problem is not the heating element, but the hi-temp (or "brown") thermostat. They cost about $25 and are very simple to install. A "Torx 1.5" screwdriver (asterisk tip) removes two screws, in back, holding top on. Lift off top, and (from the front) see silver-foil-wrapped heating assy. At lower right will be a small philips screw holding a thin wire "hasp" which holds the thermostat in place. Remove screw and hasp (without dropping in machine!), unplug two "quiik-connect" lugs (orange & red wires) and pull out thermostat to the right. New one slips right back in. Replace wires, hasp, phillips screw and top -and you're done! This is 90% sure to fix. The heating element is only about 5% likely.
One last thing ... when re-inserting new thermostat, you'll have to "wrestle" with it a bit, as the tip needs to slip into a tiny (hard to "find") hole. Keep trying, and eventually it'll fit ALL the way in, so the hasp can hold it. To purchase part, call Joel (at Malber): 800-600-8913
Oh yeah, one MORE last thing... That red wire may be burnt a little, or completely burnt in two. Radio Shack and Home Depot sell "crimp-on" lugs (1/4") like these (female). Trim back the wire, crimp a new lug on the end, and push it back onto lower terminal on thermostat. If wire is too short, of course, add a few inches of 16 guage "stranded" (lamp cord). The same stores also sell tubular "crimp-on" wire-connectors (little blue tubes) to join the old and new wires. May God bless.

Malber WD1000... | Answered on Aug 26, 2020

1 Answer

My Malber WD 1000 wash cycle knob doesn’t appear to be working automatically (won’t move thru the cycle). How do I fix?

test knob if failed replace

Malber Washing... | Answered on Apr 23, 2020

0 Answers

NEED fuse for Malber Dryer

Malber Washing... | Posted on Dec 22, 2019 | Be the first to answer

0 Answers

Malber TD 700. Where can I buy a belt for that machine?

Malber Washing... | Posted on Dec 03, 2019 | Be the first to answer

1 Answer

I need to repair a Malber WD 1000 washer and dryer, I live in Fort Lauderdale, Florida. Do you know if there is a technician service in Florida?

Malber is no longer in business. There is no more dealer or distribution network listed in Italy or the US.

You might try calling a local appliance repair to see if they would attempt the repair. Just looking online I see where Fort Lauderdale Appliance, 1040 Bayview Dr, Fort Lauderdale, FL 33304 (954) 361-2363 has a five star rating. If they don't service foreign appliances, perhaps they will recommend?

Malber Washing... | Answered on Jun 17, 2019

0 Answers

Need a capacitor for my malber wd 100. where can i find one

Malber Washing... | Posted on May 13, 2019 | Be the first to answer

1 Answer

How can I find a repairman to fix my malber p21 washing machine

https://www.hirerush.com/service/appliance-repair-service-incl-malber-appl-s_i12426

Malber Washing... | Answered on Apr 24, 2019

1 Answer

Malber W D 1000 Clothes don't dry all.

The heating element may have gone bad or is not getting current. Could be in the switch. Switch it back and forth several times.

Malber Washing... | Answered on Apr 03, 2019

1 Answer

Where can you get malber parts washer dryer combo

Internet or ebay

Malber Washing... | Answered on Mar 12, 2019

1 Answer

Where can you buy parts malber

Many sellers on eBay or the web

Malber Washing... | Answered on Mar 12, 2019

2 Answers

Spin cycle won't get up to speed!?

Might be a control board problem. Contact Malber USA at 1-800-600-8913. They will have replacement part and, if the machine is still under warranty, the part is free.

Malber WD1000... | Answered on Jan 22, 2019

2 Answers

Machine won't run through cycles automaticly

Sounds to me it might be a thermal pause, if your unit is running and then is required to heat up at a certain point and reach a certain tempurature before it advances, the heater is probably not coming on. The unit will therefore not advance.

Sgt 48

Malber P21 Front... | Answered on Jan 22, 2019

2 Answers

Spin cycle not working on Malber washing machine, it is on a used boat we just bought and it is in Fort Lauderdale but coming to NY soon, boat broker says he cant locate a person to fix the Malber- an

In New York, call Malber Distribution Corp at 516-323-5299.
They can schedule a technician to fix your machine. They've been fixing Malbers for about 25 years.
Tell them Mike, in Wash DC, says hi.

Malber WD1000... | Answered on Jan 22, 2019

0 Answers