Magic Chef Recent Questions, Troubleshooting Help & Support

You have a fault with the pump if there is nothing jamming it then the pump needs replace

https://www.manualslib.com/ Try this site

www.manualsonline.com/

Drai tube will be blocked. Please contact customer service

On top of evaporator coils

Pl. check mains supply and the plug of the microwave if every thing o.k check the fuse provided inside the oven,if o.k then the problem in the control panel,check the panel by replacing the same .

Try this site https://searchmanuals.net/search7/?keyword=%2Bowners+%2Bmanuals&gclid=CjwKCAiAqt7jBRAcEiwAof2uKwzE1jBmBNKl9hqWd4TyeToXsj80tGOrdxRc3s6LGEWtoEA-xsOXLBoCIhQQAvD_BwE

https://www.partselect.ca/Model

HOW-TO: Magic Chef Range CGS3760ADB Won't start or doesn't start

https://www.appliancepartspros.com > ... > CGS3760ADB Won't start

"Won't start" for Magic Chef CGS3760ADB? Here is why, with step by step DIY instructions & videos. s/CGS3760ADB

Check each wire going to the igniter for opens. Test both ends for continuity.

Sounds like you have a door switch that is sticking. The part for this is #DE96-00414A. Microwaves should always be worked on by a professional for safety.

Sounds like you need to replace the door switches the part number for this is 99002254. To gain access you must take the control loose. Be sure to unplug the unit before starting any work. I attached a link that may help you.

TRY TO IMAGINE TAPE OR TRY PAINTER'S TAPE TO SEE IF THE IDEA MAY KEEP SHROUD IN PLACE. IF YES, REMOVE TAPE AS IT MAY CATCH FIRE. BE EXTRA SAFETY CONSCIOUS - BUY SAFE TAPE. BUY SMALL ROLL OF ALUMINUM TAPE, WITH ONE SIDE STICKY, TO USE IN PLACE OF OTHER TAPES. CONSIDER DOLLAR STORE OR AUTO SUPPLY TAPE.

MODEL number... gas/electric would help GREATLY. Hello Chris Huff , MY very first recommendation would be to disconnect the power... and the air vent at the machine. Carefully run your hand into the machine and feel for any BLOCKAGE... lint, missing socks, snakes, hamsters ... (etc.). If the VENT is CLEAR try running the machine with a SMALL LOAD to see if you are getting past that "10 mins" you described ... ** (supervised operation with door or window OPEN). If the machine acts MORE NORMAL suspect your wall vent is the TROUBLE (needs cleaning or replacement). This is a very common cause of HOUSE FIRES... So DO NOT pretend things are "better"...\ Make sure...!! or hire a PROFESSIONAL VENT CLEANER Blocked vent will cause excessive heat... HIGH temp thermostat will stop machine for life & safety reasons. SERIOUSLY...!!

So there's a capacitor in there it's a great big dangerous and a magnatrometer which is radioactive and can hurt you too. u cant fix it and dont try transformer / capacitor /magnatrometer either or all are what is bad see the video below please leave this fix alone have a professional do it. the microwaves are very hamrful and the capacitor will kill you if you touch the high voltage terminals before properly discharging them

If it’s not visible, it’s probably hinge activated.

I am pretty sure that is a very old microwave...for example it was original equipment on a 2005 Recreational Vehicle. I am assuming you have been using that exact microwave for many years, so you are familiar with its use. If it is constantly displaying "3.5" as you say and someone has not just partially input a Time and forgotten to Cancel the Input then it sounds like a printed circuit has gone bad...

si tiene un bot?n de descongelacion es un refrigerador est?ndar. En teor?a el bot?n se dispara cuando se caiga todo el hielo del congelador si no es as?, a) "el bot?n" podr?a estar bloqueado con algo (suciedad,sulfato) b) el control de fri? da?ado espero te sirva el comentario

That would be a failed keypad, but the part is no longer available. - Ed Miller http://www.microwavecontrol.com