Magic Chef Furniture - Popular Questions, Answers, Tips & Manuals


I suspect the cooler can only actually regulate one of those temperatures and the other one just drags along behind. Perhaps the weather is now warmer and the cooler has to keep the motor on longer to keep cool. The unregulated bottom temperature ends up cooler as a consequence.

Either that or the opposite effect is doing it.

The answer might be to find a 61 degree place in your house to keep the reds.

Magic Chef... | 1,287 views | 0 helpful votes


your unit needs to have a new capacitor possibly. However, it will be next to impossible to find someone who will check it out and get the right one for this unit. Unless the unit is under warranty, I would suggest trying to get the retailer to replace it at no cost to you. If under warranty, the manufacturer should make it right? if both of those avenues are not available, then I would suggest get a new unit.

Magic Chef... | 414 views | 1 helpful votes


Fan is wired separately from the cooling unit. you may have a wire corrosion issue. take put the shelves, disassemble the back of the unit from the inside and observe the wiring to see if there are broken or corroded wires/connections. R/R if necessary.

Magic Chef Dual... | 598 views | 0 helpful votes


help us help you
What is the model number? Why do you need the manual? To troubleshoot? To operate or change settings? George

Magic Chef... | 298 views | 0 helpful votes


If the overload was open circuit you would not have a hot compressor. The overload activates because the compressor won't start. If there is a capacitor starter, change it. If not let it cool for at least a day then try again. If still no go, replace compressor.

Magic Chef... | 560 views | 1 helpful votes


You may have a Freon leak at the compressor. Running this unit at low pressure will only make it leak that much more. Have a technician check it and refill is there is a fill port available.

Magic Chef... | 1,061 views | 1 helpful votes


If the compressor is quite hot to the touch, that usually means that there is a problem with the compressor. Could be a short or open winding, but either way you will need a new compressor.

Magic Chef... | 190 views | 0 helpful votes


Mr. Ray: Did you get an answer to your question? We may be having the same problem with our Magic Chef wine cooler

Magic Chef... | 678 views | 1 helpful votes


Do you hear a hum & a click? Most likely the compressor is having trouble starting.

Magic Chef... | 128 views | 0 helpful votes


Hi Bob, did you ever get an answer to your question? I have the same problem.

Thank you,

Magic Chef... | 1,104 views | 0 helpful votes


Hold the lower zone (right side) temperature up and down arrows until it comes out of standby mode.

Magic Chef... | 1,038 views | 3 helpful votes


if there are tubes coming out of the compressor on the side that it was laid over on, then give it 24 hours just to be safe, if no tubes plug it in and let it run

Magic Chef... | 250 views | 0 helpful votes


I took the screw out but the lens won't budge and I don't want to break it. how does the lens come out?

Magic Chef... | 1,182 views | 0 helpful votes


The temp. sensor

Magic Chef... | 217 views | 1 helpful votes


You will need to replace the temperature sensor in the unit.

Magic Chef... | 108 views | 1 helpful votes


I, too, have just seen (late June 2013) the "HH" code on my Magic Chef wine cooler (and it is running too cold and I can't reset the temperature). Have you found a solution since your posting of about 1 year ago?

Magic Chef... | 4,051 views | 0 helpful votes


door not sealing ! or seal around entrance for cold air is sucking in hot air with cold air to create condensation

Magic Chef... | 111 views | 0 helpful votes


Mine was doing the same thing. Needed a new thermostat. Part number is 1206856 or WDF18A-L or WDF22A-L depending on where you get it. $23-$25 easy repair you can do.

Magic Chef... | 253 views | 0 helpful votes


Go to this page it will take you to a "dropdown" menu. Go to your model number and there will be 2 different PCBs in each category. One is for the door the other is the main. make sure you get the right one....match up the numbers you mentioned 155TD in yours which is the "pren" version of the 2 choices. Hope this helps you! http://mcappliance.com/partorder.aspx

J

Magic Chef... | 440 views | 0 helpful votes

Not finding what you are looking for?
Magic Chef Logo

177 questions posted

Ask a Question

Usually answered in minutes!

Top Magic Chef Furniture Experts

Sheldon Dedek

Level 3 Expert

912 Answers

Brad Brown

Level 3 Expert

18564 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Are you a Magic Chef Furniture Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...