Mag Innovision XJ - Recent Questions, Troubleshooting & Support


Please check the Bobbin Winder.
If the Bobbin Winder shaft is moved to the right position (bobbin winding mode), the needle will not move.
Please return the Bobbin Winder shaft to the left position and press the Start-Stop Button or Foot Control to start the machine in the sewing mode.

Mag Innovision... | Answered on May 14, 2011


Sounds like your TV has a PIP (picture in picture) that allows your AVI (audio visual input) to be viewed simultaneously with your cable input. Check the manual for the correct buttons, but the one you're looking for says either PIP or AVI or something along those lines. Hope this helps

Mag Innovision... | Answered on Apr 13, 2011


the problem is most likely to be found on the HOrizontal Output Transistors note their numbers and replace them.this transistors are usually mounted on huge heatsinks.

Mag Innovision... | Answered on Mar 19, 2011


Your PC video resolution is set too high for the monitor to display, you need to lower to the highest the monitor can support and for the best picture.
http://www.fixya.com/support/r4873371-fixing_out_range_format_not_supported

Mag Innovision... | Answered on Jul 09, 2010


loose board solder...

Mag Innovision... | Answered on May 09, 2010


open the monitor if you are technical person look the EHT (a big part in the monitor) has preset attached .read the name focus on it rotate it by screwdriver in active on condition untill you are satisfied

Mag Innovision... | Answered on Apr 07, 2010


What you can do is go to a good computer hardware store like, new egg. or somewhere that sells core hardware for computers. you should be able to buy a PCI-E or a PCI ESata card so you can plug it in. hope this helps!

Mag Innovision... | Answered on Apr 06, 2010


hello. Just push the start button. Joe

Mag Innovision... | Answered on Mar 19, 2010


Hello there !

There could be a problem with the picture tube it could be dead( shorting) or the tube Transformer s damaged another course of this could be at the Horizontal section ie a Transistor or a Diode could be shorted .
Pls tell ur Technician to check all this .
Lastly Buy a new Monitor .

Good luck

Mag Innovision... | Answered on Dec 05, 2009


Try to change the refresh rate of your monitor and/or reduce the resolution.

Best Regards

Mag Innovision... | Answered on Oct 22, 2009


its overheating or the lamp is bad, get some canned air and spray the inside with the air.

Mag Innovision... | Answered on Sep 30, 2009


I would try a degauss first, see that that gets rid of it.

Mag Innovision... | Answered on Sep 09, 2009


What you are seeing is the high frequency equivalent of an echo. This is normally caused by external received signal problems rather than the set itself. Note that one of the images is stronger than the other; this is the primary received signal. The weaker one is occurring a few microseconds later and is being received as a reflection from a building or a poorly terminated cable. Repositioning your antenna or replacing your cable will probably help a lot.

Mag Innovision... | Answered on Jun 07, 2009


This is usually a convergence problem.. Could you update this with the model number please. That will allow me to give you some specifics about what could be wrong and how to fix it.
Dan

Mag Innovision... | Answered on Jun 02, 2009


this is a ez one go to setting and change the brightness if that dose not work tll me at [email protected]

Mag Innovision... | Answered on May 29, 2009


It depends on what kind of programs he needs to work. I work with AutoCad 2008 and Google Sketch Up Pro Version 6 for my Architectural work on a low end PC. With a Pentium 4 @ 1.5 GHz, 512 MB RAM, and a small HDD, so you do not need much. Pretty much the cheapest new PC you can buy would be perfect. Hope I Helped!

Mag Innovision... | Answered on Jan 28, 2009


ptc or decosing coil is bed or notworking proper so u have replace it

Mag Innovision... | Answered on Jan 15, 2009


from experience i have noted that after some time the Horizontal Out-put Transistor (HOT)gets worn out.This is a big black transistor starting with cd,d,t etc mounted on a big heatsink.note the numbers and replace it.

Mag Innovision... | Answered on Dec 20, 2008

Not finding what you are looking for?
Computers & Internet Logo

579 questions posted

Ask a Question

Usually answered in minutes!

Top Mag Innovision Computers & Internet Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Cindy Wells

Level 3 Expert

6178 Answers

Are you a Mag Innovision Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mag Innovision Computers & Internet

  • Forum

View Most Popular

  • Mag Innovision Computers & Internet
Loading...