LG WM - Answered Questions & Fixed Issues

The hose from the soap drawer to the tub may be split. These hose have flexible ridges and its common for them to split inside one of the ridges.

1. Make sure the washing machine is properly leveled and that the load is balanced inside the drum. An unbalanced load can cause the machine to shut off.
2. Check the power cord and outlet for any visible damage or loose connections.
3. Check the control panel for any error codes or messages that may indicate the source of the problem.
4. Check the door latch and hinges to make sure they are functioning properly. A faulty door latch can cause the machine to shut off.

only suggestion, next time it happens, unplug like you've done and then hold in power button for 15 seconds to see if that resets it.

You can check it at https://www.us-paydayloan.us/

I had this problem with another model LG washer dryer and the problem was just the tiny switch (6mm x 6mm) on the circuit board had worn out. They cost about 30 pence on eBay and are very easy to remove and re-solder onto the circuit board as there are only 2 pins. This saved a huge amount of money for a new control board.

I did all the steps to ensure was right soap and amount, used cleaning tablets to keep odor down. I took it in my own hands and made an overflow and vent. Self explanatory with pictures. More than a year, no suds, no odors. the exit has a short incline to avoid normal splash and the fan on secondary catch chamber keep a constant low air movement. Two outdoor electrical boxes, fan, and pvc, I know, overkill.... Hope it helps someone.

My wife has been complaining that the bleach and fabric softener dispenser still had water in it after washing. After removing the top to the washer I found that there are 4 components to the dispenser. 1. the solenoid (part of a 3 solenoid bundle) for the cold water, 2 the controller to the solenoid 3. The hose from the solenoid to the dispenser, and 4. The dispenser. After checking that there were no kinks in the hoses. I checked the solenoid found it had power at the right time but the flow was low. I shut off all the water and disconnected the lines going into the back of the washer I found that the cold water filters were clogged. After cleaning them (there were 2 for each hot and cold) The washer worked correctly.

Question edited to add that it is an LG Washing Machine and not a Sump Drainage Pump. Question moved from Larry's Computer category. Please ALWAYS include 'make model (what it is)' in all questions. This model is very little known and parts are not available. The funky connector is so that you can only use LG spares. https://www.google.com/search?q=lg+wf-t1122tp+parts You would have to find a pump that fits and change the connectors on the washer to match the connectors on the pump. Normally insulated spade connectors.

Washer will not drain: The drain water pump is the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure to check the pump to be sure a small object like clothing or similar has not lodged itself inside of it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed. Read more:  HYPERLINK "http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/" l "ixzz3X2LbXMWJ" http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ The washing machine drain hose is where the water flows through to get the water out. If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the water from the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it The water pump belt (to drain out the water) may have broke or become frayed or loose. If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing the NO DRAIN issue and remove and replace if needed. If the lid switch is not working as required it will cause your washer to not drain (and many other problems). This may be unlikely as a bad lid switch will usually cause your washer to also not agitate or spin. However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuity My advice is free cuz God is good!

Several reports in Australia of brand new LG Washer/Dryer combo (model number WD14700RD) getting dHE error's with very 1st dry cycle.
I bought a LG WD14700RD last week, and yup, washed fine.

Dryer cycle results in dHE error.
Everytime.
Cycle stops & you just have to power off the machine.

Service man found several possible causes.
He unscrewed the top of the machine off & said dHE errors are related to the dryer components. He started a dryer cycle & watched & lisened to machine.
He observed the dryer fan was not starting up.
He unplugged the power cable to the dryer & replugged.
The fan now started up, but only with cold air.
He then looked towards the front of the machine & noticed several cables had come loose from their sockets, one he identified was the heater element cable.
He plugged that back in & another unknown cable was also loose. He plugged that back in.
It worked.
dHE error gone & dryer fan started & pumped out hot air.

It seems at least a few of these machines during transit (from South Korea?) fail due to cables coming loose from their sockets.
dHE errors result if fan cable & fan heating element cable come loose.
My thanks to WAM electrical repairs in Box Hill (Melbourne) for helpfull advice & successfull repair.
For people looking at buying this machine, it washes & now dries perfectly well & I am happy with the machine.
But beware that this problem is out there (there are several other reports I read) and it have this problem, which is easily fixed but does require a service call out, under warranty of course.
Steve, East Melb.
[email protected]

Yes and check hinge

It is funny I don't know why nobody will listen to the original post I too have a LG Tromm. I am getting the either 6E or bE he is not mistaken when he says this is the code that comes up the same thing is happening with mine any answers would be greatly appreciated?

We have the same problem with our LG washer. Don't think the door can be adjusted but I'm not for sure. I think the gasket is wore out but haven't checked on fixing the problem yet because it barely leaks.

may be a belt problem since you have this sound
thank you

No. Actually, the Hall sensor, part number 6501KW2002A, is covered by a 7 year part warranty.

CD means cool down, press the pause start button, the door lock will open. It is an anti crease cycle. It mentions it in the owners manual, but it is hidden deep in the drying section.
Sgt 48

My guess is replace the drain pump. Inexpensive part but kinda hard to get to. Check out repair videos on parts sites or YouTube

No electronics involved in reversing a LG dryer door. On a difficulty scale of 1 - 10, it rates about a 2. Go for it.

There is also a discharge lint filter on the front lower left that has to seal properly. If the water appears only when washing, you can probably eliminate leaking from the water supply side up to the solenoids controlling the water. The most likely source is a leak in the rubber section between the tub and the front door, a leak in the seal between the door and the washer, a leak or overflow in the soap dispenser, or a leak in the discharge side components. You could probably figure out the source if you could view these areas during a cycle, but that would require some disassembly of the cabinet so that you would need to know what you were doing.

Your drain pump assembly impeller has most likely deteriorated. I just replaced the assembly on my unit. There are actually two small motor/pumps. I would recommend replacing them both. You will find the videos of how to do this on youtube. I bought the parts off of Amazon