LG Washing Machines - Page 7 - Recent Questions, Troubleshooting & Support


WHILE IT IS LOADING WATER, TRY TO ADVANCE THE WASH PROGRAM; INSTEAD OF LARGE CAPACITY GO TO MEDIUM.

LG Washing... | Answered on Aug 28, 2019


Need the model number the number you provided is not the model

LG Washing... | Answered on Aug 24, 2019


If your getting water coming out. Your pump is not working or is clogged with a coin check the hose. And have a shop vac ready to suck up the water. The door has a lock and should not open on front loaders till the cycle is complete and water is drained

LG Washing... | Answered on Aug 16, 2019


Hi from retired Englishman in SW France,

'de' does stand for Door Error. There is likely to be a problem with either the lid/door solenoid/lock or the 'lid/door closed' sensor becoming apparent with the extra movement of washing requiring a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

LG Washing... | Answered on Aug 15, 2019


Take top off, take control panel off, remove front panel.

LG Washing... | Answered on Jul 23, 2019


Could be the water valve

LG Washing... | Answered on Jul 22, 2019


Most likely it is a broken 'spider'. That's the 3 armed part that holds the inner drum to the hub. Not uncommon. Can be expensive to fix. Can be done yourself. Check out videos on YouTube or repairclinic or appliancepartspros.

LG Washing... | Answered on Jul 21, 2019


Most top load washers have snap clips in front and hinges in back. You use a putty knife or equivalent to push in the clips(located between top and front of unit in the seem). Some others have screws on bottom near the legs that you unscrew and tilt front forward and then lift up and off. Good luck.

LG Washing... | Answered on Jul 20, 2019


PE= pressure error. A water level error. Check hose to pressure sensor. Is it connected? Does it have a hole in it? Otherwise replace pressure sensor.

LG Washing... | Answered on Jul 17, 2019


Check your exit hose spigot, it may be clogged. This is if your filter is all clean. There should be air for passage in the standpipe behind. Your hose should not fit airtight into the standpipe and neither too deep into it. Snaking out your standpipe would be good too. If all this does not work, check your pump for blockage.(ref manual re pump)

Rate me pl.....if helped.

LG WFT1071TP Top... | Answered on Jul 14, 2019


It could be damaged or worn bearings. It can also be a broken spider. The spider attaches to the inner drum and is part of the spindle assembly.

LG WD-80130F | Answered on Jul 12, 2019


I'm sure you double checked, but I have forgotten to plug the connectors from the control back together before putting the top back on. Seems obvious but I've done it more than once. Good luck. (And make sure your house breaker isn't tripped)

LG Washing... | Answered on Jul 08, 2019


The lid has hinges on the back so it rotates back from the front. The front is held in place but two metal clips. Push a metal spatula in the seam between the top and front to release the clips. Clips are about 1/4 in from each side.

LG Washing... | Answered on Jul 04, 2019


i would guess you are getting a "tE" error code. that is a bad thermistor. pretty common. and it starts out as an intermittent error. it really is an easy fix. great online videos. check out appliancepartspros.com for both video and parts or repairclinic.com for video and parts. or youtube.com

LG TROMM WM2688H... | Answered on Jul 02, 2019


If this is a front loader and older model check the spider arm on the back of the drum it may be corroded and putting the drum off center at low speed. I just replaced the drum to tub gasket and the spider arm which was severely corroded (name may not be correct go to the LG parts site)

LG Washing... | Answered on Jul 02, 2019


I just finish repairing my LG front loader and this sounds like the same issue. The back of the drum has a spider arm and spindle arrangement (think that the name) the spider are was corroded and broke after 10 years, this puts the drum off balance and chews up the gasket. I had to also repair the wash tub where the drum had worn into it and JB Weld worked fine. It all seem to work fine now.

LG Washing... | Answered on Jul 01, 2019

Not finding what you are looking for?
LG Logo

Family Lines

11,894 questions posted

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6136 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...