Lexmark Recent Questions, Troubleshooting Help & Support

printer uses USB A to USB B Printer Cable readily available on line less than $10.00

The 1203 error indicates either a communication problem between your cartridges and your printer or a short in one of the cartridges. Please follow the steps below to identify and fix the issue:

1. Make sure the printer is on.

2. Open the printer cover. The print cartridge carrier moves and stops at the loading position, unless the All-in-One is busy.

Note: If the carrier does not automatically move to the center, turn off the printer/unplug the printer from the power source and then slide the carrier to the center.

3. Remove both cartridges from the carrier.

4. Close the printer cover.

5. Re-brick your printer. Pull out the power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds.

6. When the printer turns on, reinsert one cartridge first.

7. Close the printer cover and check for any errors.

8. If no error appears, reinsert the other cartridge. Close the printer cover.

9. Replace whichever cartridge is causing the error to appear with a new cartridge. Then try to print a document again to verify that the problem is fixed.

go to menu and look for language and get the right language you want.

http://support.lexmark.com/index?page=content&locale=en&productCode=&segment=SUPPORT&clearQuestion=Y&userlocale=EN_US&id=HO3026 That is a general printer error Check for jams or blocks. you might have to delete the driver and clean the registry I use revo uninstall. then install the latest firmware Sir Dana

The 200.16 jam indicates that the input sensor was covered when the printer was powered on or reset, or a cover was opened/closed.

You may also check the following:

1. The paper being used is within specification and has been loaded correctly.

2. Any previous jams have been completely removed.

3. The printing environment is within acceptable temperature and humidity ranges.

4. If the tray was overfilled or a paper jam occurred, sheets of paper may have come off the media stack.

5. If you don

You can unplug the printer from the wall, then leave it off for about 30 seconds then plug it back in. That should reset the printer, if not read what the message says on the screen, or you may have to navigate through the settings to see the error message.

There are no controls on the Output Tray, only on Paper Trays. http://publications.lexmark.com/publications/lexmark_hardware/MS81x/UG/pdf/Lexmark_MS81x_UsersGuide_en.pdf https://www.google.com/search?q=Output+Tray+status+lexmarK ..

the tray that has the mystery sized paper in it ? are you using a4 sized paper ? look at the bottom of the tray for adjustable plastic sliders Are the sliders set on same size as paper size you are using ?

please you chack your printer fuser unite thermostater is over toner dust clean it i wish you are success

Here is the manual; led status diagosing starts on page 13:
http://www.lexmark.com/publications/pdfs/2007/e250/EN/ABJug.pdf


Click on this link or copy and paste the complete link into your browser.
If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Could be photoconductor at end of life.

You shoul still be able to do a printer test print (press the arrow button).

Look on the printed pagesfor Toner AND Photoconductor.

These show as OK when new or very low count, and 100% when fully used.

If the toner is showing as 100% when you've just replaced it, either the chip is faulty, the wrong one, or if the cartridge is a remanufactured one possibly nor been replaced.

There is a Paper Menu option somewhere in the menus on the op-panel. You need to go to the Paper Type option and change the Paper Type for Tray 1 to plain paper. You can also hit the Select button when you get this message and you will print.

Problem Error: "200.xx Paper Jam"; Error: "200.01 Paper Jam"; Error: "200.11 Paper Jam"; Error: "200.16 Paper Jam"; Error: "200.21 Paper Jam"; Error: "200.22 Paper Jam"; Error: "200.25 Paper Jam"
Solution.

Hope helped.

Here's an article in the Lexmark website on Error: "201 Paper Jam" or "202 Paper Jam". This will guide you on where to locate the cause of the problem. Follow the instructions. But if you're having a really hard time locating it or you need more assistance, don't hesitate to contact Lexmark Technical Support. Thanks.

Verify your settings under the Paper Menu are correct as far as size and type. All trays with same size and type settings are automatically linked as per the User Guide.

Resetting or reinitializing the network card's NVRAM will clear all TCP/IP configuration information. To have a record of this information, it is recommended that you print a network settings page prior to performing the reset procedure. Press to print both printer and network settings pages.

1. Turn the printer off.
2. Press the left front cover release button and pull the front door down.
3. Press and hold while powering the printer On.
4. Release when the LED is illuminated. NOTE: Be patient as the LEDs will light up in multiple patterns before finally stopping at
5. Close the front cover. NOTE: Observe that the , , and LEDs will be illuminated at the same time. This is known as the Home position.
   OPTION: Have the customer hold down to print a "Printer Diagnostics" menu page.
6. Slowly press the button until the , , and LEDs are illuminated. NOTE: Normally, this will require you to press the button 11 to 13 times, depending on the options and features installed.
7. Press and hold until all LEDs flash or strobe from left to right, then release the button. Wait until this process stops with a pattern of three LEDs that should resemble the Step 6 pattern.
8. Press and hold until the light pattern returns to the pattern of four LEDs in Step 5 or theHome position.
9. Turn the printer Off.
10. Turn the printer On.
    NOTE: If on a DHCP network, wait 30 seconds to see if the DHCP server/router sends out an IP address to the device. A settings page will automatically print if this is successful. A longer wait may be required on other networks.
11. Press to print the settings pages and observe that all the TCP/IP settings have been reset.
12. Reconfigure the device using DHCP, Auto IP (zero configuration) or the IP Setup Utility.

Hope this helps.

Pull back the fuser cover ( black upper area) and look for the jam beneath the black roller with paper sticking up - to pull it out

Please check if the paper guides on the paper tray are correctly positioned. For example, if you are using a letter sized paper, make sure the guides are set to 8"x11".

After installing a new cartridge and the blinking light is on Toner Low, it means that the photoconductor is almost full and should be replaced soon. Press and release the Continue button (green button) to clear the light sequence and continue processing the print job. If the light is still blinking, replace the photoconductor kit.

For further assistance, please call Lexmark Technical Support.

On the left side, near the pichup roller, of the tray there should be a "flag" hanging down in the elips hole. See if it is hanging down or stuck in the "up"position.If so pul it down and the machine should work fine again.