Lanier Logo

Lanier Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 130 Products
  • 618 Answers
  • 30K Views

That code is usually a problem inside the laser unit - the polygon mirror motor.

Lanier Office... | Answered on Dec 14, 2014


That is from a dirty thermistor in the fusing unit. It is the one touching the pressure roller.

Lanier Office... | Answered on Dec 14, 2014


Depends on the associate engine code. Most of the time it means that maintenance is overdue. Otherwise, it is an electronic issue.

Lanier Office... | Answered on Dec 14, 2014


No bottle, it is inside the transfer belt unit that hangs on the inside of the right hand door. Dump it and put it back.

Lanier Ld345... | Answered on Dec 14, 2014


The waste toner is contained inside the belt unit that is mounted on the inside of the right hand door. Remove the screws that hold it together and dump it. Very messy so be careful. The message will go away by itself.

Lanier 5235... | Answered on Dec 14, 2014


The error code is not related to the toner. What model?

Lanier Office... | Answered on Dec 14, 2014


ricoh-usa.com

Lanier Ld 116... | Answered on Dec 14, 2014


Metal tab on right side of copier is bent and correctly touching the duplex unit interlock switch. Open the duplexer and notice the metal tab stick out. Put back to a 90 degree angle.

Lanier Office... | Answered on Dec 14, 2014


That is the master clamper area. Take off the rear cover. From the rear it is on the right. There is a motor and a rack gear that moves to open the drum master clamper when removing and loading a master. With the back cover removed, try to make a master while watching that assembly. You can also put the drum in and drive the motor by hand to watch and see if opens the drum clamper.

Lanier Office... | Answered on Dec 14, 2014


Press the telephone button first with one finger and immediately after you press that button press the rewind button, The unit should go into rewind and erase should be flashing on the digital display. When the unit starts rewinding take your finger off of both buttons, if you keep them on ,then the unit will rewind and stop erasing .

Lanier Audio... | Answered on Dec 10, 2014


Some times the battery contact need to be pulled out a little bit. they are located down inside the battery compartment. You can stick a small screwdriver under the battery contact and bend it upward for better contact. If that doesn't work try removing the back cover and tightening the grounding screw, which is a silver screw located by the motor pulley hole. Sometimes this screw loosens up and then the ground is lost to the entire unit

Lanier Audio... | Answered on Dec 10, 2014


It is under the flap located directly under the keyboard buttons. It is a slide switch and you can adjust it for a little recall or a lot of recall.

Lanier Audio... | Answered on Dec 10, 2014


There is an intermediate rubber roller that keeps the unit from "eating" tapes. When this roller gets dirty or shiny then it slips and the unit will eat tapes. It needs to be cleaned with a q-tip and some alcohol. It runs between the flywheel shaft and the take-up spindle. You should be able to clean it if you take off the bottom cover.

Lanier 260T... | Answered on Dec 10, 2014


This unit most likely has a broken rewind/fast forward rubber belt. This is a very common problem and is easily fixed if you can acquire a new belt. Any place that services Lanier equipment should be able to easily fix this problem.

Lanier Audio... | Answered on Dec 10, 2014


Look under the front of the unit and there is a tel ans switch this must be on to enable the unit to answer the call

Lanier Audio... | Answered on Dec 10, 2014


If you want to record somebody 3-4 feet from you then use the dictate mode. If you want to pick up voices in a large room then use the conference mode, it increases the microphone sensitivity to the maximum level.

Lanier P165... | Answered on Dec 10, 2014


Come into test mode, if it comes back the fuser service needed. -Carl

Lanier Ld345... | Answered on Dec 01, 2014


Its the brown belt thing on the right door, take off the 2 springs and remove the belt assy and empty, very messy...-Carl

Lanier Office... | Answered on Dec 01, 2014

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Lanier Experts

Brad Brown

Level 3 Expert

18342 Answers

Ekse

Level 3 Expert

13434 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Lanier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...