Kyocera FS - Recent Questions, Troubleshooting & Support

You may need an imaging unit. VERY expensive.

Kyocera... • Answered on Jul 14, 2020

If you wish to get some details; check the site linked here. Pull up older posts..

Kyocera... • Answered on Feb 29, 2020

Looking to get rid of 'Install MK' message - any way that i can reset so i dont have to purchase a main kit?

Kyocera FS2020D... • Answered on Feb 28, 2020

press manu button then go to service then press right errow key goto status page press double enter it will print around 5 or 6 page in second page in down you can find the serial number or else see the back side of the printer it should stikared.............

Kyocera FS-2000D... • Answered on Nov 08, 2019

the top of the waste toner container must be cleaned 100% from the toner because it should be a light sensor that has to pass through it , if its spoiled with toner the light cannot pass through it ,so i recommend you to empty the waste toner container first and wash it with water and drying it well before using it again.

Kyocera FS-2000D... • Answered on Nov 01, 2019

After removing paper tray, above the paper tray slot, on the bottom of unit, left side, is a green tab. Pull metal flap down, remove paper, and your in business. That is just my experience with my friends unit.

Kyocera FS4020DN... • Answered on Oct 15, 2019

Drum unit non- installing error

The drum unit is not installed or not installed properly. You must have knocked it loose.Install the drum unit (See page P.1-5-10).11_23_2011_12_47_14_pm.jpg

Kyocera... • Answered on Oct 08, 2019

The message you get is from the fuser setting for printing envelope. At the back of the printer, you have a handle wich opens the back dor. There is located the fuser (fixing unit) that will slide back. On left and right of the fuser, you can see 2 green buttons. In your case one of them or both are pressed. If you press one time, the button goes down. If you press again, the buton rise up. Try to press them down.

Kyocera FS2020D... • Answered on Sep 30, 2019

Once you have installed and setup a multi-tray printer you might like to try to print a document to different printer trays. Open a word document and create a two page document.
  • Select your new printer under file->Print (if it's not the default)
  • Click the page layout tab
  • Click the small triangle at the bottom right
  • Open the page setup dialog box and click the page Paper Tab
  • Choose a tray for the first page and other pages. Close the dialog box and print.

Kyocera... • Answered on Sep 28, 2019

The most common machine failure codes is CF---. For example CF248, CF000. In the most cases the printer is need to be upgraded to the latest firmware.

Kyocera FS... • Answered on Sep 25, 2019

1087 1087 163 print key

Kyocera FS-1016... • Answered on Aug 18, 2019

F000 is a panel communication error... update firmware... firmware as far as i know isnt available to the public... contact kyocera

Kyocera FS-2000D... • Answered on Jul 29, 2019

F248 is communication problem ,it some times happens when the printer cannot understand the data coming from the computer from certain program's or a specific file .reset the printer clear any print jobs on the pc and try print a test page if you're still getting that error you will need to get a service engineer to upgrade to the latest firmwarec

Kyocera... • Answered on Jun 27, 2019

Error Code 6000 is fuser code, you need to replace the fuser unit, make sure there is no paper stucking there first! I’m happy to help further over the phone at

Kyocera FS-2000D... • Answered on Jun 18, 2019

make sure dial on front of cassette matches paper size in cassette

Kyocera... • Answered on Jun 13, 2019

LSU cleaning motor error

When the LSU cleaning motor

is driven, an error signal is

detected continuously for 1 s.

Defective connector

cable or poor

contact in the connector.

Reinsert the connector. Also check for continuity

of the connector cable. If none, replace

the cable.

Kyocera... • Answered on May 27, 2019

Can you be more specific or provide error codes or messages?

Kyocera... • Answered on May 05, 2019

In some cases you can reset the C 6000 - when is a false error.
try this:
1. Go to Menu/System and browse till you see
press and hold: # START ENTER
The "Service" will go away and browse to "Maintenance".
2. Press ENTER to go in maintenace mode - the display change to Maintenance mode.
3. browse to 0163 and press ENTER - reset fuser
4. pick EXECUTE and press ENTER
5. turn the copier OFF, wait 20 seconds and power up the machine.
If C 6000 goes away it was a false error if NO ...try again and if the C6000 persist means the thermal fuse it is blown so you have to replace the fuse = call for service.

Kyocera... • Answered on Apr 10, 2019

Not finding what you are looking for?

1,789 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Kyocera HP Expert
Kyocera HP Expert

Level 3 Expert

532 Answers


Level 3 Expert

85239 Answers

George Mclaughlin

Level 2 Expert

370 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Office Equipment & Supplies

  • Forum

View Most Popular

  • Kyocera Office Equipment & Supplies