Krups XP - Recent Questions, Troubleshooting & Support

0helpful
1answer

Error code OE

circuit board need resetting
5/14/2020 2:40:05 AM • Krups XP7225... • Answered on May 14, 2020
0helpful
1answer

Error Code 5 on Krups Expressario EA 8010

Tenho uma krups ea8010 aparece c?digo de erro 05 s? pede a manuten??o e ficam as luzes todas acesas j? fiz todo o processo de limpeza e n?o sai dai
3/31/2020 7:41:34 AM • Krups XP4030... • Answered on Mar 31, 2020
0helpful
2answers

How do we get past a message to remove/ refill the water tank?

ChoccyBar, THANK YOU. You're answer was so helpful. I have the XP7230 and all of the sudden had exact same problem, machine wouldn't not register a full tank. After reading this I checked the floating piece and saw that it was not floating with a full tank like it is supposed to. Had to obstruct it to keep it afloat as well, and voila, it worked. Ahh... what a relief to have my machine working again. Coffee has never tasted so good.
3/15/2019 12:15:23 PM • Krups XP7230... • Answered on Mar 15, 2019
0helpful
1answer

Krups XP4030 Espresso Machine

sounds like the tubing slipped off its connector inside the machine. Pump is sucking air.
10/24/2018 11:31:03 PM • Krups XP4030... • Answered on Oct 24, 2018
0helpful
1answer

The water pours out the sides when I make

the gasket needs to be replaced. I just had to replace mine. http://www.krupsonlinestore.com/product_detail.asp?T1=KRW+MS-620342&MENU=&SELECT=&SKW=xp4030
10/24/2018 11:27:14 PM • Krups XP4030... • Answered on Oct 24, 2018
0helpful
1answer

Krups XP4030 is stuck in the steaming mode

Here is a link for the manual. It says on Krups web sight they have a 1 year warranty,
http://www.krupsonlinestore.com/manual/55360.pdf
9/18/2018 10:27:26 PM • Krups XP4030... • Answered on Sep 18, 2018
0helpful
3answers

Error Code 9 on a Krups XP7240 Expresso machine

After I changed piston sealing I get the same error 09. It was caused by missing connection to the thermoblock temperature sensor. In my case both connectors for thermocouple were cracked. They are located directly on the body of thermoblock, below two fuses, covered by rubber housing. After I solder them again on the position error 09 disappeared. Unfortunately it is necessary to open at least front panel of the machine. Moreover I tink that there is also important to save polarity of those two cables.
7/12/2018 11:40:48 AM • Krups XP4030... • Answered on Jul 12, 2018
0helpful
1answer

Krups 4000 coffee machine wont make strong coffee

Maybe the grind is too fine and it is building up too much back pressure. Max is normally around 15 bar, more than that and the pump stops functioning. Also try another silver bucket that holds the grounds, if it is double walled sometimes grinds too small can block them between the skins. There was often a single wall bucket available that eliminated the blockage problem.
1/28/2018 11:47:18 PM • Krups XP 4000... • Answered on Jan 28, 2018
0helpful
1answer

My Krups XP4000 Espresso Machine

The pump is probably bone dry, you will need to put some water into it under pressure. I have a piece of hose in my workshop that fits the seal that the tank engages into, it's about 8 to 10" long. I engage the hose, fill it with water, activate the pump and seal my mouth over the hose and blow as hard as I can like I'm blowing up a balloon, it rarely fails.
11/16/2017 1:00:31 AM • Krups XP 4000... • Answered on Nov 16, 2017
0helpful
1answer

Water won't flow out of espresso machine

Did you check to see if the heating element is not open?
9/9/2017 3:43:33 PM • Krups XP 4050... • Answered on Sep 09, 2017
0helpful
3answers

Espresso maker doesn't work properly

It is clear that there is a problem with water supply. Check if pump works, if it does, there is blockage in water supply to pump. Check and clean.
8/7/2017 1:48:44 PM • Krups XP2070 10... • Answered on Aug 07, 2017
0helpful
2answers

My machine won't power on, as soon as it's plugged in the LCD flickers, could it need a new control board?

Sounds like the power supply to the board you mention is struggling, does it read anything intelligable?
7/25/2017 12:34:19 PM • Krups XP2070 10... • Answered on Jul 25, 2017
0helpful
1answer

Krups XP4000 Pump Espresso Machine.

If it is brand new you should not be expected to figure it out, take it back to the shop. Any messing about with a brand new appliance can only harm your guarantee, let them figure it out. It sounds like the pump valves are dry or stuck.
5/2/2017 7:33:59 PM • Krups XP4030... • Answered on May 02, 2017
0helpful
1answer

Filling of the machine necessary

Code 05 for my KRUPS EA 8050?
2/24/2017 5:24:40 AM • Krups XP7230... • Answered on Feb 24, 2017
0helpful
1answer

My Krups coffee maker is leaking some coffee onto the counter

no normal fix it requires worshop inetervention to replace the seal
1/6/2017 10:38:18 AM • Krups XP7230... • Answered on Jan 06, 2017
0helpful
1answer

What happens to the cofeteire is locked

Nothing happens.
8/28/2016 3:42:25 AM • Krups XP7230... • Answered on Aug 28, 2016
0helpful
1answer

XP4020 - n1164

Krups XP 4020 Semi-automatic Espresso Coffee Maker http://www.coffeemachinemanual.com/krups-xp-4020
5/26/2016 6:34:36 AM • Krups XP Coffee... • Answered on May 26, 2016
0helpful
1answer

Dead No power

Hello
You can get replacement parts here
http://www.belstar-electrics.co.uk/
they are very good and will help
3/16/2016 8:18:18 PM • Krups XP2070 10... • Answered on Mar 16, 2016
Not finding what you are looking for?

16,778 questions posted

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Pierre Laplante

Level 3 Expert

2061 Answers

Ross Keen

Level 3 Expert

1365 Answers

eyecam

Level 2 Expert

100 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Krups Coffee Makers & Espresso...

  • Forum

View Most Popular

  • Krups Coffee Makers & Espresso...
Loading...