Konica Minolta bizhub - Recent Questions, Troubleshooting & Support
Service mode 92729272 password not working
Okay. That is a KM code. I need more detail to answer your question. for instance, model #, and why do you feel you need to get into service mode? If you don't know where you are going and why you are going there, there is plenty of buttons and bits that can cause further issues with your machine.
Bizhub 367 error c6756 how do I resolve this issue
C6757: CCD power-supply voltage malfunction
Description: Power is not supplied to CCD after the lapse of a given period of time after the main power switch or power key is turned ON or the machine recovers from the sleep mode
Check:
• CCD board (CCDB)
• Scanner drive board (SCDB)
• DC power supply (DCPU)
Error code c0202. What is
Most likely there is paper stuck in the very back behind one of the trays. Take both trays out and see if there is any paper jammed (could be a small piece). Put trays back in but leave them open, turn off the printer, unplug it, wait 5 minutes, plug it back in, turn it back on and push in the trays.
SMB Scanning
I had the same issue and fixed it by adding the group "Everyone" to the shared folder permissions (where I was sending my scans) and assigning the "Everyone" group rights to "change" and "read".
How to find the MAC address for a konica minolta
I know this is and old post, but I came across this issue today and this post is the first that came up in my Google searches, and three was no good response. So I thought I would post an update.[Sorry Zaheer, I know you were trying to be helpful, but your response was a little too vague and in the end, inaccurate]1) Go to the printer's Web Connection by typing the IP address in a browser. 2) Make sure you are on the "System" tab (Blue) at the top3) Click on the "Detail" link on the side menu4) Click on the "Interface Info" sub link* Notice that you do NOT log into the Admin portion of the Web Connection. That will only confuse you.This will show various stats, one of which is the MAC Address of the machine. It seems like this would be better placed in the Network tab under the admin interface, but here it is.Hope this helps someone.
Hi, I have code 2452 Bizhub c6501
C-2451 to C-2453 error codes are lit even if the Developing Unit, developer, and Charging Unit are replaced. This is a symptom from a customer who mostly prints black. If you increase toner density, it will be good.
Hello my machine Bizhub 600 is indicating an error code C8101 when switching it on, who can i solve this
Actually C8101 is on Rank B meaning by Open / Close the front door to clear it.
But if error code still appear, Check the connector between M3-relay CN5-DFCB J15 for proper connection and correct as necessary.
Check the connector between PS12-DFCB J15 for proper connection and correct as necessary.
Check the connector of M3 for proper drive coupling,and correct as necessary.
PS12 I/O check, sensor check
M3 operation check (change M3)
DFCB F8 conduction check
Warming up error code 2 2 hours warming up my machine bizhub 600
Sir/Mam,
Have you had the developer and drum replaced recently, or does the screen say Replace PC Drum? There are certain house chores the copier does before "Ready to Copy" it is waiting for them to get done, so that equals "Please Wait". One big item is making sure the developer and toner are properly mixed inside the image unit underneath the drum or next to it depending on the series. Might want to have the developer replaced and drum/cleaning blade normally done all together, then run the F8 procedure/Developer Charge, and make sure the counters where cleared. Did you recently replace the drum and the developer if so did you clear the counters for the drum and developer, FIRST? IF not then the copier thinks the new drum and new developer are old. The copier works on the counters that is how it knows it got a new drum and developer. Get new developer and a new drum and have it installed correctly. Counters are clear before the unit is yanked out of the machine, then you remove the image unit/drum unit replace the developer/drum and cleaning blade. (DO NOT USE A VACUUM CLEANER WHEN REPLACING THE DEVELOPER static electricity can destroy the sensor located below the developer unit. Then reinstall and RUN F8/Developer Charge. Make sure the fax line and Ethernet cable is removed can't print anything until the F8 is run. Or you will start all over again with new developer and a new drum.
Not finding what you are looking for?