KitchenAid Ovens - Answered Questions & Fixed Issues


I had a similar problem today with my KitchenAid Superba wall convection oven (2002 model). I was roasting tomatoes at 225 degrees F for 3 or 4 hours when the control pad changed and showed that the probe was in use (never have I used it and had to look for it). I, too, tried to plug in the probe and take it out, but nothing changed. My worry was that I could no longer use the timed bake function. After trying to reset by turning off the oven at the breaker, with no change, I turned on the oven to 400 F and left it on for 10 - 15 minutes hoping that the high temperature would dry out whatever moisture that must have gotten in the place where the probe connects. Then I turned it off and just waited. After a half hour or so the control pad cleared and nothing showed (that is what you want when the oven is off!). Everything is back to working now.

KitchenAid... | Answered on Nov 21, 2020 | 14,951 views


Request the Superba model kebc107kss03 manual directly from KitchenAid.

KitchenAid Ovens | Answered on Oct 29, 2020 | 354 views


Is it possible you've blown a breaker? Probably a double-breaker, 220V.

KitchenAid Ovens | Answered on Oct 27, 2020 | 19 views


the latch the hooks into the door is caught inside the slot where it locks into when in self clean,you have to move the latch,unplug it,look through the air vents or slots up above the door if you can get a screw driver in there try to move the latch or if you can get something down inside to move the latch,i used a plastic long wire tie to do this before,i slid the tie down around the metal hook part of the latch that locks into the door,and pulled it to the left and got the door to open,it got hung up in the hole and the door wouldn't open but what ever works you have to move the hook part of the latch to get the door open,you can try picking up on the door to see if you can get it open or you'll have to pull the oven out and take the top off to get at the latch,hope this helps

KitchenAid Ovens | Answered on Jul 04, 2020 | 893 views


In our case, the error code was displayed on a KitchenAid microwave/oven combo. It turned out to be a $4 fuse called the "Main Cavity Fuse". Good luck.

KitchenAid Ovens | Answered on Mar 04, 2020 | 147 views


This happened to me three times with a brand new oven, they kept coming back and replacing the fuse. I finally made the Kitchenaid dealer replace the whole oven, never happened again.

KitchenAid... | Answered on Oct 04, 2019 | 241 views


Hello Susan Bailey,
Typically "THEY" do...
It would be really great to know if we are talking about a USA domestic product...
or another NATIONALITY.
Other countries normally have FUSES in the
appliance cords.

Find your MODEL NUMBER and go to a PART/SPARES
supplier ( I like appliancepartspros.com )
-> appliancepartspros.com
If this is a "MICROWAVE" the FUSE will start popping because the MAGNETRON has deteriorated
and is CONSUMING it's own energy.

I can be a LOT MORE specific if you provide a
model number (pretty please).
Read minds... Cannot rally do...!!
https://en.wikipedia.org/wiki/Carnac_the_Magnificent

KitchenAid Ovens | Answered on Jun 25, 2019 | 161 views


F5 - E1 Self clean latch will not lock

1. If door latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to door switch, then from door switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Replace door switch.
  4. Re-apply power.
  5. Press and hold any key down for 1 minute to clear F5 failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
2. If door not latched:
  1. Disconnect power from unit.
  2. Check wires and connectors from control to latch switch, then from latch switch to control. If no damage to wires and all connectors okay, proceed to step C.
  3. Repeat steps A and B for door switch.
3. Measure door switch (door open = switch open small low voltage terminals). Replace switch if defective.
4. Measure latch switch (unlatch = switch open, CAUTION - oven light contacts are closed). Replace switch if defective.
5. If corrections are made in any step, reconnect power to control. Press and hold any key for 1 minute to clear R failure code from memory. F2 will appear. Press CANCEL and observe for 1 minute to ensure operation is correct.
6. If failure remains, disconnect power and replace control.

Note: Applies to all F5-E... codes.

KitchenAid... | Answered on Jun 19, 2019 | 542 views


Hi. try to reset this unit by killing the power or unplugging the cord for 5 minutes. this will reset the control. if the control continues to beep after you reset, this will confirm control failure. you will need to replace the control board in this case.

KitchenAid... | Answered on Jun 19, 2019 | 679 views


I am having the same problem, how did you fix it?

KitchenAid ... | Answered on Mar 01, 2019 | 998 views


Possible Solutions

Reset power to the product:

There may be a problem with the Oven Appliance Manger Control or the associated wiring.
  • Power unit down by turning off the circuit breaker(s) for one (1) minute.
  • Power unit up by turning on the circuit breaker(s).
  • Monitor the oven for one (1) minute to ensure the error code does not display again.
  • Verify oven operation.

Still need help? Call or schedule service.

KitchenAid Ovens | Answered on Feb 02, 2019 | 474 views


Yes

KitchenAid Ovens | Answered on Sep 15, 2018 | 254 views


the is an external fan which draws all the moisture away,pull oven out and follows the two wires frm the and make sure both are connected and connected so it is alive when oven is on, if good the probaly a faulty fan

KitchenAid Ovens | Answered on Jul 15, 2018 | 100 views


KitchenAid KODE507ESS

(this MAY be your model??)... you did not specify?...

This link MAY have your DISPLAY PARTS:

KitchenAid Range Stove Oven Display Board

Anthony

KitchenAid Ovens | Answered on Jul 09, 2018 | 1,146 views


From the Site:

"F2-E6 - Cancel Key Line Open - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. Select the 'cancel' function and wait 60 seconds. If error code reappears then replace the touch pad, or touch pad and control board (clock) if all one assembly. All F3-E Codes - Oven Temperature Sensor (RTD) or Warming Drawer Defect - Replace oven temperature sensor (RTD)."

Kitchen Aid Appliance Fault Codes

Hope this helps!
Anthony

KitchenAid Ovens | Answered on Jul 09, 2018 | 165 views


yes you wilkl need to remov ethe micro from the oven mountingin order to access the light bulb (dumb-design) but no way around it

KitchenAid... | Answered on Jul 09, 2018 | 964 views


switch off electricity to oven, then switch it back on - that reboots the computer that controls the oven.

KitchenAid... | Answered on Jul 09, 2018 | 892 views


your door or interlock switch is not closing press on the door see if it stars if so you will have to check you alignment if not the switch could be bad you wuill need to open the ctrl panel to get to the switches unplug first

KitchenAid... | Answered on Jul 09, 2018 | 370 views


send me am e mail at [email protected] with the model number

KitchenAid... | Answered on Jul 09, 2018 | 530 views

Not finding what you are looking for?
KitchenAid Logo

Ask a Question

Usually answered in minutes!

Top KitchenAid Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

jdthefixer

Level 3 Expert

747 Answers

Are you a KitchenAid Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...