KitchenAid Kitchen Ranges - Page 9 - Answered Questions & Fixed Issues

You asking how to Level the entire range? Most Like refrigerators have adjustable feet that need moving in the direction like a screw. You going to need a Level (duh!), some 2x2 wood, and a fulcrum(something to lift the oven up a little). BE SURE YOU HAVE A) REMOVE UNPLUG POWER B) GET ANOTHER PERSON TO HELP YOU LIFT! While gradually-slowly lifting oven place 2x2 by 6inches long under the oven on both sides. Now you can see the feet and start turning them and they will extend (clockwise usually). Once you do ONLY the front two, repeat the same for the back two. Now you can tell your helper by placing the Level every which way usually three different directions while you adjust the feet till they are level. If this person doesn't "Get It", Be nice and say thank you and find someone who does! (don't Use Your Wife, if married to one)

You need a new thermostat. Thats the wire looking thing inside the oven that has a metal test-tube looking thing at the end.

Hey! why don't you ask a HARD QUESTION! Really? You have a board in hand AND NOW! You want to install it? Is this electric or gas (stalling) doesn't matter! Here is a video to explain it best. Oh I have a question? Do you buy Bullets first and then go get the Gun? Never Mind....

will need to disconect from power then remove the cover on back to get to remove screws hand

Check power to bulb base. Replace bulb.

it sounds like the wire that goes to the stove igniter is shorting out when you are using the oven.

If you have checked the power outlet and switched it on, there is no way of diagnosing further from such a vague question. Is it completely dead? in which case it could be a fuse. More info would help

Try disconnecting range from power source for 20 minutes and allow to completely cool down. Reconnect and try.

Sounds like it will not explode, but it surely may start a fire somewhere. I should recommend you to have someone unplug it ( if it can be unplugged) or turn off the circuit breaker if it is "hardwired " into the house or apartment. Please have it checked by an expert before you try to use it again. Be blessed.

mustn't be an american oven, guy

Fro memory these have the igniter pack at the rear of the oven once you get the cooker out it's pretty easy to remove & replace it. If you are unsure ring the manufacturers service division they are usually happy to help.

You will need the model number & serial number which may be on the back of the cooker on behind the plate under the oven door, then contact the manufacturer or agent. Reece HVAC are also a very good source to obtain parts from.

You will need to replace the spark module. Here is that part to order. Whirlpool W10475150 Module Spk AppliancePartsPros com

I do not know your unit but it sounds like one of the fuses has failed if you have them. If burners work then probably the thermostat. This is just a guess.

Beth, you either have a failed convection element, part number 9460769, possible bad terminal connection at the element or a failed oven control. A bad element is the most common failure. replacement instructions for a failed heater can be provided.

thermostat my be brokenit thinks its hot so it shuts the heat off....

Usually under the cover on the lower right side

Either the knob has gone out or the burner element. I would test the knob first to see if there is current when turned to the large zone. If the knob is working, next would be to test the burner to see if the outer ring has burned out. I would guess more likely the control has gone out. Burners have less failure (typically).

first off ,,,electric ovens dont have pilot lights ,,,its electric..the burner is electric....now ,,on a gas oven thats different..first remover the old one,,,then replace with new following reverse directions from removing the old one ....

The latch is stuck halfway! Take your finger and push the latch all the way to the right until the oven light goes out. Now hold it there and press the self clean button. Let it start up for a few seconds then hit the off/cancel button and let go of the latch. It should hear it made a winding like sound as it goes back to it starting position.