KitchenAid Kitchen Ranges - Page 9 - Popular Questions, Answers, Tips & Manuals
Repair control board for Kitchen aid KESC308LSS0
The problem is the solder joints on the white wire connector on the control board. If you unplug and carefully remove the control board and look carefully at the solder connections for this connector you will see that some of them are cracked or broken. One way to tell is to take a small screwdriver and gently push the pins as if to push them through the backside of the board. The faulty ones will move. Reposition them and resolder the connections. Problem solved.
1/16/2014 2:20:12 PM •
KitchenAid...
•
306 views • 0 helpful votes
Self clean and oven light
The latch is stuck halfway! Take your finger and push the latch all the way to the right until the oven light goes out. Now hold it there and press the self clean button. Let it start up for a few seconds then hit the off/cancel button and let go of the latch. It should hear it made a winding like sound as it goes back to it starting position.
2/10/2014 2:46:49 AM •
KitchenAid...
•
152 views • 0 helpful votes
Oven temperature way too hot
The ohm's on the temp sensor is adequate if measured at normal room temperature. Next check the wiring from the sensor connector to the control board for continuity. Also verify there isn't any corrosion on the connection to the board. If that is good, visually inspect the control board for burnt areas as that will be the only other component in that function. This control board is NLA but you may find one stashed in someone's old inventory.
2/8/2014 5:35:49 PM •
KitchenAid...
•
106 views • 0 helpful votes
Kitchenaid stove code f68
This stove should absolutely still be under warranty. I would start with calling the KA customer service. They are pretty good and will usually do all they can to help you. The number for them is:
800-422-1230
1/3/2014 2:00:26 AM •
KitchenAid...
•
246 views • 1 helpful votes
Hood lights not working
Faulty switch for the lights? Measure the voltage in the lamp sockets - if you don;t know how, find someone with electrical experience to check it out.
11/21/2013 3:09:38 PM •
KitchenAid...
•
497 views • 0 helpful votes
Tappan series 110 the igniter is glowing but it wont lite the oven
Is the gas turned on at the stop valve behind the range? Assuming the gas is on, the igniter can glow but not actually be working properly such that the control valve does not open or the valve may be failed. There are electrical measurements for the valve and igniter and related circuit that can be made if you have a clamp on amp meter and a volt meter.
11/18/2013 10:54:28 PM •
KitchenAid...
•
357 views • 0 helpful votes
F11 and beeping
Unfortunately the f11 error means the clock is shorted. I have actually seen this issue several times on this unit. Its not your fault and theres nothing you did or could have done prevent this issue. You need to have the clock replaced to fix the error code. The clock on this model is the brains of the operations.
Here is the part to order.There is also a video on that parts page to
show you how to make the repair.
All
parts come with a 365 day, any part, any reason return policy.
10/25/2013 12:20:37 AM •
KitchenAid...
•
539 views • 0 helpful votes
When I turn the oven on, there is a fan that comes
yes this will work for you, but before you change out the fan motor make certain the fan blades are unobstructed and not rubbing against anything this can make quite a horrible noise as well.best regards Falco
11/4/2013 8:48:08 PM •
KitchenAid...
•
349 views • 1 helpful votes
Not finding what you are looking for?