Kirby Vacuums - Recent Questions, Troubleshooting & Support


Contact Kirby direct

Sentria - The Kirby Company - Kirby Vacuum

https://www.kirby.com > earlier-kirby-models > sentria
The Sentria Model includes softer lines and gentler curves on its design, giving it a sleek and soft look. The handle was redesigned on this model to provide ...

Kirby Vacuums • Answered on May 31, 2021


try running motor without belt if still gets hot motor overheating if doesnt get hot make sure belt not slipping

Kirby Vacuums • Answered on Dec 14, 2020


The switch has become defective and will have to be replaced.

Kirby Vacuums • Answered on Dec 07, 2020


It could be that you have the brush settings wrong for your carpet type. Check if the brushes are on number 3, if so, try dropping them down a notch or two and see if that does it. I think that the brushes when spinning spin towards you, so when pulling the vacuum back, the brushes are helping to drive, when pushing forward, you are pushing against the brushes. If the brushes are sticking out too far, it could cause bouncing/jumping. HTH :)

Kirby G6 Bagged... • Answered on Oct 07, 2020


I just solved the problem. Go to this website: http://www.completevac.com/kirby_schemo_5.html
It will show you where the spring goes (left side inside the ratchet - when you remove the ratchet you will see that it is hollow. That's where the spring goes!) and a good picture of that assembly

Kirby G6 Bagged... • Answered on Mar 07, 2020


HELLO,
PLEASE SEE MY TROUBLESHOOTING GUIDE...

http://reviews.ebay.com/COMMON-PROBLEMS-WITH-THE-KIRBY-VACUUM-TROUBLESHOOTING_W0QQugidZ10000000003800312

MANY OTHERS HAVE HAD SUCCESS WITH DIAGNOSING AND FIXING THEIR OWN KIRBY USING MY GUIDE. I HOPE THAT YOU ARE ONE OF THEM... :0)

MARCI

Kirby Ultimate G... • Answered on Nov 01, 2019


There is no other way to clean mattress except by using a vacuum cleaner. It is because when you use water in cleaning your mattress, this might start molds especially when the mattress layer has remains of moisture. If you want to have a stain free, spotless and moisture-free mattress, use a mattress pad. Or you may use a waterproof mattress pad to avoid unwanted stains in order to keep a clean mattress at all time. A waterproof mattress also protects your mattress against undesirable odor and has maximum protection ability. Click the below link to know more. How to Keep Your Mattress Clean by Moazzem Hossain

Kirby Shampooer... • Answered on Sep 13, 2019


I had the same problem and I called my local Kirby guy, he's great, helped me when I thought I blew my kirby up, it was just a cord and he wa able to tell me that over the phone. When I called him with this problem, he knew right away that it was only putting out a thin strip in the middle only. The first thing was I needed that little screen, the second was the hole where the screen goes has a white tube that goes from that hole to the bottom of the tank, its kinda in the corner and I never thought it would have anything to do with the problem. He said I needed to run hot water in it and clean it cuz I was going to have to blow in it, yes, with my mouth. I ran it under hot water for a few minutes and then with hot water in the hole, blew into it. I did this a few times, checking the tube ending each time. After a few times, water was shooting freely through the tube. Problem solved, I think, I'll be shampooing tonight so i'll know for sure then. An alternative to blowing with your mouth would be using a can of air, didnt think of it till now and I have 1!

Kirby Ultimate G... • Answered on Sep 08, 2019


There should be a definite audible click when you press down on the switch. Most switches also latch so that there is a little play in the foot switch when it is on. Possible problems included - blown fuse in the plug, damaged cord, failed starter capacitor. It may be an idea to take it to a local vacuum repair store and get an estimate for repair.

Kirby Vacuums • Answered on Aug 18, 2019


Remove rear housing /3 screws and one under cover. Remove wires with paperclip install screw clip and reinstall. Also one screw under rear wheels , loosen don't remove as it helps hold lower section on the switch.

Kirby Vacuums • Answered on Jun 05, 2019


If you are using the correct shampoo then the tank my need to be replaced. They will clog if tank wasn't cleaned after last used. Check that the dial is open and both filters are in place , add water and shampoo and test without the hose connected . If you still have no suds coming out then just order a new tank.

Kirby Vacuums • Answered on May 14, 2019


The switch bar is bent , and needs to be replaced. You can try to re-bend it but this takes some skill. Take the bar out and lay it flat and you will see the where to straighten .

Kirby Vacuums • Answered on May 14, 2019


You can pry them off , just make sure they go back on the correct end.

Kirby Vacuums • Answered on May 14, 2019


Watch this YouTube video:


https://m.youtube.com/watch?v=rmpbFD_V2MU

Kirby Vacuums • Answered on Apr 23, 2019


The conversion of Amps to Watts is governed by the equation
Watts = Amps x Volts

For example 1 amp @ 110 volts = 110 watts
your case 7 amp @ 120 volts = 840 watts
unless you are running it at 230v but I don't think you can
I would look for one rated for Volt-Amps instead of watts
It's best to round up to be safe add 40 - 60 watts

Don

Kirby Ultimate G... • Answered on Apr 17, 2019


make sure it has a clean bag and not clogged up

Kirby Ultimate G... • Answered on Feb 20, 2019


make sure not full of hair or other debris

Kirby Vacuums • Answered on Feb 20, 2019

Not finding what you are looking for?
Kirby Logo

2,132 questions posted

Ask a Question

Usually answered in minutes!

Top Kirby Vacuums Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Paul Bade

Level 3 Expert

1688 Answers

Brad Brown

Level 3 Expert

18693 Answers

Are you a Kirby Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...