Kenwood Logo

Kenwood Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 75K Answers
  • 2M Views
0helpful
1answer

My kenwood A701A runs too fast on the minimum spees setting. is there a way to slow it down?

Replacing the motor controller may fix it, if it is faulty. screenshot 2024-06-16 at 06.18.09-undefined-undefined-0.png Refer to a Kenwood Chef service agant.
6/16/2024 5:19:41 AM • Kenwood Food... • Answered 3 days ago
0helpful
1answer

My Kenwood chef a701a is running too fast at slowest setting. How can I adjust the speed?

Hi Philip,

The slow speed on your Kenwood Chef A701A might be running a bit fast due to wear and tear over time. The good news is that there are two screws you can adjust to bring the speed back down to around 60 rpm. Here's how to do it:

Unplug the mixer: Safety first! Make sure your mixer is completely disconnected from power before attempting any adjustments.

Locate the adjustment screws: There are two small screws with springs underneath them, typically near the motor housing area. You might need a flashlight to spot them better.

Make small adjustments: Using a screwdriver, turn each screw by a quarter turn clockwise at most. It's important to only make small adjustments because over-tightening can damage the mechanism.

Test and repeat (if needed): After adjusting the screws, plug the mixer back in and turn it on to the slowest setting. See if the speed feels slower and more controlled. If it's still too fast, repeat step 3, making another quarter turn adjustment to each screw, then test again.
6/14/2024 9:25:55 PM • Kenwood Food... • Answered on Jun 14, 2024
0helpful
1answer

Kenwood Kid60So17 delayed timer won't work

Make sure you open the door, press "on", load the dishwasher, select the program, press delay length and THEN close the washer.
6/14/2024 6:24:19 PM • Kenwood... • Answered on Jun 14, 2024
0helpful
1answer

Intructions for use of kenwood cream maker A927

Can anyone help I'm looking for the a927 manual cream maker many thanks
6/14/2024 12:55:53 PM • Kenwood KM305... • Answered on Jun 14, 2024
0helpful
2answers

How do I disassemble a Kenwood KMix hand blender model HB894? Does anybody have some service manual? Any disassemble diagram?

There is a name plate, it is glued on so you need to prise it off. Underneath is a tab - press it along with the other two on the side and the motor assembly slides out.
6/10/2024 1:15:22 PM • Kenwood kMix... • Answered on Jun 10, 2024
0helpful
1answer

F6 error in kenwood split ac

I have kenwood invertor AC, i get P6 error on display.. what to do??
5/22/2024 12:08:15 AM • Kenwood Heating... • Answered on May 22, 2024
0helpful
1answer

How can i remove the plastic cover from the

you will not be able to fix the coil yourself, it will have to go back or to a specialist. the set up will be far to close tolerances and how are you going to reset it and balance. leave this to Kenny.
5/15/2024 10:33:46 AM • Kenwood 12"... • Answered on May 15, 2024
0helpful
7answers

My Kenwood DC inverter Air conditioner compressor didn't start and shows number 36 after 3 minutes on indoor unit digital display.

can not find much here but it seems like the air filter is pluged
5/9/2024 3:23:39 PM • Kenwood Heating... • Answered on May 09, 2024
0helpful
1answer

Kenwood A-58 amplifier power auto switch off

The cause is generally a short circuit speaker lead causing failure of one or more amplifiers. That makes the power supply shut down reducing any more damage to the surrounding circuits. Take it to an Authorised Kenwood Hi Fi repair shop for evaluation.
5/5/2024 4:20:55 PM • Kenwood Car... • Answered on May 05, 2024
0helpful
5answers

Sharp Stereo- Protect Mode??

Try plugging in a pair of headphones. I tried it without the speakers connected and since it found the headphones and they were OK the system came out of protect mode.
5/1/2024 1:10:06 AM • Kenwood XD-655... • Answered on May 01, 2024
0helpful
1answer
0helpful
2answers

No display lighting up.

The first thing to check is the solder connections on the display itself. The display should have a series of pins that you will see on the PC board that is behind the front panel. Resolder the connections on either end. These are the connections that supply both the +and - sides of power. These often develop poor connections. Update this with the results of the resoldering and we'll continue from there if the problem is not resolved.

Dan
4/27/2024 9:00:53 PM • Kenwood Audio... • Answered on Apr 27, 2024
0helpful
1answer

My kenwood kdc-u2159b display call n no sound out

Me radio kdc2159b is displaying the ward call,how do i remove it
4/14/2024 10:44:35 AM • Kenwood Car... • Answered on Apr 14, 2024
0helpful
1answer

Kenwood surround sound receiver krf-7050d stuck on mute

Check the Remote Control: Ensure that the remote control is functioning correctly. Press the MUTE button on the remote control to unmute the sound. The "MUTE" indicator should turn off. Manual Adjustment: Navigate to the receiver's setup menu and locate the audio settings section. Adjust parameters such as bass, treble, balance, and surround sound modes to achieve your desired audio quality. Physical Connections: Verify that all audio cables are securely connected to the appropriate inputs and outputs. Check if any cables are damaged or loose. Speaker Configuration: Make sure your speakers are correctly configured. If they are set to "Mute", unmute them. Factory Reset: Refer to the instruction manual for instructions on performing a factory reset.
4/3/2024 3:18:34 AM • Kenwood Audio... • Answered on Apr 03, 2024
0helpful
2answers

I have an old model

Hi there,

As another South African citizen I can sympathize with you when it comes to finding service & after care support.
Kenwood S.A.'s website tells you to take it back to the store where you purchased it. Great help that is?
They do however give a JHB number where you can contact them:
011 474-0153

Let me know if you have no joy from this number.

Best wishes,
Graemevm
4/2/2024 6:02:11 PM • Kenwood Food... • Answered on Apr 02, 2024
0helpful
1answer

I have a kenwood ka-129 which is currently muted

No, you must press mute again on the remote to toggle off mute.
3/31/2024 9:08:56 PM • Kenwood Audio... • Answered on Mar 31, 2024
0helpful
1answer

Need to know how to disable remote function for a Kenwood stereo integrated amplifier ka-129

You could put a peice of gaffa tape over the sensor window if you do not read schematics very well.
3/31/2024 9:07:55 PM • Kenwood Audio... • Answered on Mar 31, 2024
Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Kenwood Experts

Brad Brown

Level 3 Expert

19187 Answers

ADMIN Eric
ADMIN Eric

Level 3 Expert

39637 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

67789 Answers

Are you a Kenwood Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...