Juki Sewing Machines - Recent Questions, Troubleshooting & Support


check for cracks in the oil pan perhaps a coating of epoxy is needed .

Juki Sewing... | Answered on Sep 16, 2020


There are a few things you can try -
1. Extend the bobbin thread longer outside and push it away from you.
2. When you make the Stiching pressure lever down then see whether it sits properly or is lose and creating gap.
3. Clean the bobbin seat. Check for its free movement.

Juki Sewing... | Answered on Aug 21, 2020


If the solenoid has failed the fuse may not be affected. A solenoid is a big switch so they can fail without blowing the fuse. You may need to replace the solenoid.

Juki Sewing... | Answered on Aug 17, 2020


To be sure it is top thread, suggest you try a thread of a different color other than the bobbin.

Assuming its top thread, you need to increase top thread tension.

Other causes; Uneven feed of top thread can cause nesting of top thread. The machine uses a horizontal spool for top thread. Be sure you use a spool cap that is as big or larger than the spool. Pay particular attention to threading instructions on which direction the thread drops from the spool. If backwards, flip spool.

See following video, testing tension

https://m.youtube.com/watch?v=YF7EOCvpHLg&feature=youtu.be

Comment below for further assistance.

Juki Sewing... | Answered on Jul 23, 2020


ALL MACHINES YOU NEED TO HOLD THE THREAD WHEN STARTING TO SEW TO PREVENT PULL OUT

Juki Sewing... | Answered on Jul 19, 2020


maybe thru a sewing machine shop

Juki Sewing... | Answered on Jun 14, 2020


hi there
regarding Error E924 at JUKI control it means Motor driver failure ( Motor driver has broken.) or you can first check motor connection if connected secure or there's lose connection. other ways try to change motor with new one or check control box only with working machine to confirm Error coming from motor or control box.
BEST REGARDS
ASHRAF
CAIRO - EGYPT
[email protected]

Juki DDL-8700 | Answered on Jun 03, 2020


Turn it to either extreme and then see if the feed dogs hit the plate when you hand turn the hand wheel towards you. Sometimes the feed dogs or plate have been replaced and they have set the stich length so that the feed dogs won't hit the ends of the plate.

Juki Sewing... | Answered on May 30, 2020


If straight stich slide plate is in position only straight stitches are available.

See pg 31
http://www.juki.co.jp/household_en/hsm/pdf/40166931_DX-2000QVP_EG_20151019.pdf

Juki Sewing... | Answered on Apr 23, 2020


With the needle, bobbin and bobbin casing removed, Force it with the hand wheel in the normal direction of travel. You can't break it. It will free up. Then run it for 30 seconds at full speed. If it does it again, it needs serving and the timing adjusted.

Juki Sewing... | Answered on Apr 19, 2020


https://www.youtube.com/watch?v=Mw0iFamTYMs

https://www.youtube.com/watch?v=CakM3FWKmGc

Three beeps that repeat after a pause and occur when you power on your computer indicate a problem with the system memory. Three beeps that play and then stop as the computer starts successfully mean that the BIOS was restored.
https://smallbusiness.chron.com/three-consecutive-beeps-mean-computer-79697.html


Juki Sewing... | Answered on Apr 18, 2020


You should make sure it is grounded. Also, is it getting oil from the pan? Blown fuses usually mean there is an overload in the motor. Check that the belt is not too tight.

Juki Sewing... | Answered on Apr 16, 2020


https://www.youtube.com/watch?v=6PGPtkjsqus

Juki Sewing... | Answered on Apr 05, 2020


Check fuse "F1" located on power filter module see service manual at following link.

https://www.manualslib.com/manual/522958/Juki-Tl-2010q.html

You might get lucky and the fuse saved you.

Juki Sewing... | Answered on Mar 21, 2020


The Needle Tool and the small screwdriver that came with it.

https://www.youtube.com/watch?v=YtR6JKKMDJ8

Juki Sewing... | Answered on Mar 18, 2020

Not finding what you are looking for?
Juki Logo

1,617 questions posted

Ask a Question

Usually answered in minutes!

Top Juki Sewing Machines Experts

Cindy Wells

Level 3 Expert

6163 Answers

Charles Tidwell

Level 3 Expert

475 Answers

Irene Tulloch

Level 2 Expert

498 Answers

Are you a Juki Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...