After conducting an extensive search, I have found that the best place to purchase a replacement water tray for the Florcraft model 709-3917 is directly from the manufacturer or an authorized dealer. The manufacturer's website, www.florcrafttools.com, offers a variety of replacement parts for their products, including the water tray for the model 709-3917. Additionally, authorized dealers such as Home Depot and Menards may also carry replacement parts for Florcraft products.
It is important to note that purchasing replacement parts from unauthorized dealers or third-party sellers may result in receiving counterfeit or incompatible parts, which can be dangerous and potentially damage your equipment. Therefore, it is recommended to only purchase replacement parts from trusted sources.
In summary, the best places to purchase a replacement water tray for the Florcraft model 709-3917 are directly from the manufacturer's website or an authorized dealer such as Home Depot or Menards.
Based on the information provided, it seems that the Norcold N611R fridge in the travel trailer is experiencing issues with cooling on AC power. The green and yellow LEDs are blinking, and the fridge stops cooling after running for a random number of hours. The gas cooling seems to be working fine, and the fuses, AC/DC power, and power board have been checked and replaced.
One possible cause of this issue could be a faulty heating element. To check if the heater is working properly, you can use a multimeter to measure the resistance of the heater. The resistance should be between 44 and 52 ohms. If the resistance is outside of this range, then the heater may need to be replaced.
Another possible cause of this issue could be a problem with the thermostat or temperature control system. If the temperature control system is not functioning properly, then it may not be able to maintain a consistent temperature in the fridge, which could cause it to stop cooling after a certain amount of time.
It is also possible that there is an issue with the wiring or connections in the fridge. If there is a loose or damaged wire or connection, then this could cause intermittent cooling issues.
In order to diagnose and fix this issue, it may be necessary to consult with a professional technician who has experience working with Norcold fridges.
A blinking orange light on appliances such as refrigerators and freezers indicates that the "supercool" or "superfreeze" feature is active. These features are designed to quickly cool or freeze the contents inside the device. A flashing light serves as a visual cue that the unit is actively working to quickly cool or freeze food. Once the desired temperature is reached, the light will stop flashing, indicating the unit has completed the cooling or freezing process.
It seems that you're referring to an issue with the DIM32D2BSSPR Ice Maker model. When the unit goes through several cycles, it shuts down and the three size selector lights start flashing. Holding down the power button allows you to reset the unit and resume its operation.
Based on the provided information, it appears that there may be a malfunction or error occurring within the ice maker. Here are a few steps you can try to troubleshoot the issue:
1. Check the power supply: Ensure that the ice maker is properly connected to a stable power source. Verify that the power cord is securely plugged in and there are no loose connections.
2. Clean the unit: Ice makers can sometimes experience issues due to debris or mineral buildup. Clean the ice maker thoroughly, including the ice bin, water supply lines, and any filters or screens. Follow the manufacturer's instructions for cleaning and maintenance.
3. Reset the unit: As you mentioned, holding down the power button allows you to reset the ice maker and get it working again. If the issue persists, try performing a factory reset if your model supports it. Refer to the user manual for instructions on how to reset the unit.
4. Contact customer support: If the problem continues to occur despite your troubleshooting efforts, it's recommended to reach out to the manufacturer's customer support or service center. They can provide further assistance, troubleshoot the issue over the phone, or recommend a professional repair service if necessary.
Remember to consult the user manual specific to your model for any additional troubleshooting steps or guidance provided by the manufacturer.
All questions need full 'make model (what it is)' please.
Do you have a freezer at the top and a fridge below it? That box is just a cold air vent from the freezer. There is often a circulating fan in there, but it could be elsewhere.
The issue with a warm fridge and a cold freezer is that the defrost for the freezer has failed and the evaporator is a solid lump of ice and not passing chilled air, OR, the vent is boked with ice. The is a defrost timer and a heater element at the rear of the freezer back panel.
If the refrigerator freezer is cold but the refrigerator is warm, the defrost thermostat might be defective. Several times a day the defrost heater turns on for a few minutes to melt away any frost that may have accumulated on the evaporator coils.Mar 3, 2015
Yes we do. Is this yours posted as 'Anonymous'?
My problem is that my water timer will open the valve for a manual watering, but when it's the time I have set for it to come on, the valve doesn't open.
That is a problem with the electronics controlling the timer. Return it to them for servicing.
..
EMER position. Alternately displays current time and temperature. the HOLD mode. HOLD is displayed flashing when the thermostat is in a temporary HOLD Mode
Question edited for better English and CAPS for maker name.
Yes, that is exactly how it is supposed to work and is called 'cycling;. 15 minutes between cycles is perfect. What happens is this. Your fridge is at the perfect 3' centigrade (37.4 Fahrenheit), so it cycles off the compressor motor, 15 minutes later the temperature rises to 3.2'C (37.76'F) so the compressor cycles on for a few minutes and pulls the temperature back down to 3'C. If you are opening and closing the door or adding things at ambient room temperature like supermarket produce, the compressor will stay on longer to get that perfect temperature and cycle off.
If it is doing it every 30 seconds, that is called 'short cycling', and it would need attention.
..