Jacuzzi Garden - Page 2 - Recent Questions, Troubleshooting & Support
Hot tub in EC with light flashing
Ecn or Ec Message
Ecn or Ec MessageIf
the Ecn or Ec Message is Alternating with the Water Temperature on the
Display, the Spa is Operating in the Economy Heating Mode.If the
Ecn or Ec Message is ON Solid (Not Flashing) on the Display, the Spa is
Operating in the Economy Heating Mode, but there is No current water
temperature because the Spa is between Filter Cycles.Ecn or Ec is Alternating with Temp:The Spa is Operating in the "Economy" (Ecn or Ec) Heating Mode.The
Water Temperature is Sampled Only during Programmed Filter Cycles. The
Heater will Only operate and Heat up to Set Temperature during the
Filter Cycles. The Water Temperature will probably drop Below Set
Temperature between Filter Cycles. Other Heating Modes are Standard,
Standard in Economy, and Sleep Modes.Ecn or Ec is ON Solid (Not Flashing):The Current Water Temperature is "Unknown" (- - - or - -) while in Economy or Sleep Mode.Between
Filter Cycles, while in the Economy or Sleep Heating Modes, the Pump
has not turned ON and the Last Water Temperature is not Current. To
read the Current Water Temperature, either Change to Standard Heating
Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.
No temperature display cant set temperature
Located behind the access panel there is a grey box that is the spa pack. Open that up with the 2 screws on the top of the pack. There is a small glass fuse on the circuit board. One of those fuses is most likely blown. If that is not the culprit you need a new topside control. More than likely it's the fuse.
How to dismantle a jacuzzi magnum pool filter pump
When you go to loosten the lock ring you will need to find the lock tab that will keep it from comming off. This tab I think will pull out but it may push in and this will free the ring to turn. Once this is off if the motor runs turn it on for a second and let it push the front and back half apart. If it won't run you can use a flush bag to pressure it off. In worst case you can pry the halvs apart with a big screwdriver. If you do this be careful not to hurt the case of the pump it is just plastic.
When the pump is opener you remove the difusser and look inside the impeller. If you have a screw in the center of the impeller it will be a left hand thread so to remove you will turn it clockwise. Now just unscrew the impeller turning it counter clockwise and take the rear plate off the motor by removing the four bolts on the back. Good luck.
Motor hums, but does not start..
turn off power open access panel and check pump close water valves to pump and disconnect lines ckeck pump for debris that may be stuck in pump blocking impeller if clear than lube motor bearings and try moving impeller back and forth to free motor once free return and test pump
I have a Balboa WH-R576-DCAH.
If the pressure switch is jumped properly and you still are not getting a call for heat, then you are having a problem with the circuit board and it most likely is going to need to be replaced.
If the heat light is coming on but no voltage is going to the heater, this would also indicate a bad board.
You can find the
52213 circuit board online at:
http://balboadirect.com/52213.aspx.
Hope that helps.
The hot tub heater keeps
This is likely an issue with the GFCI breaker not being ableto handle the load or a problem with the high speed of the pump.
You can find answers to common spa orbath problems online at
http://www.balboadirect.com/support.aspx
Hope that helps!
Understand that this information isbeing provided as-is and without warranty or guarantee. As with allelectrical components and devices, all work should be performed by a licensedspa or pool technician. Serious injury or death can occur if a component isimproperly repaired or installed.
I have a balboa control
Press the TEMP Button to change between EC, ST & LS Mode and then press the LIGHT Button to select the required Mode.
We bought this house 4
Hi,
I will advice you get a technician to come to your house and take a look at it, since you are sure of the position or status of the Balboa jacuzzi, it will be better you get someone, a professional to help take a look at it, this is not (DIY) do it yourself as you can see.
I HAVE A MAGNUM FORCE PUMP. iT WAS RUNNING THIS
It could be the capacitor again, but most likely if it stopped while running, its not that, unless you had a brief power failure. The motor may have a built in thermal overload which turned the pump off. If it only humms then it could either be locked up by something in the impller, or could be the bearings in the motor have failed. If the motor doesn't smell "burnt" then you might stand a change to disassemble the pump. Disassemble the motor and replace bearings. Replace the mechanical seal while you have it apart. OR you could buy a new motor, as it is 10 years old.
Not finding what you are looking for?