Icom Radio Communications - Recent Questions, Troubleshooting & Support

0helpful
1answer

ICOM IC-R6 is scanning very slow. 1 frequency in 2 second, not 100 frequencies in 1 second. Where is problem ? How to change speed of scanning in IC_R6 ?

The Fix Programming via CS-R6 with Windows 10 made the problem. Scanning was very slow. The CS-R6 program through Windows 10 made problems with the scanning speed - it became very slow, one frequency in 2 seconds instead of 100 frequencies in one second. Through programming CS-R6 on Windows 7, the scanning speed returned to the corresponding one in the ICOM instructions - 100 frequencies per second
10/9/2022 9:56:12 PM • Icom Radio... • Answered on Oct 09, 2022
0helpful
1answer

I finds very difficult to read a particular station in my icom 718

Hi, please move the radio away from it's current position to attempt to find alternative position where it's frequency will be transmitted clearly as intended. Also, please keep away from any microwaves or speakers so as not to cause any interference. Thank you.
6/14/2022 6:13:10 PM • Icom Radio... • Answered on Jun 14, 2022
0helpful
1answer

I find it difficult to read a particular station on my Icom 718 HF Base Transceiver.

IS this a frequency issue? A modulation issue? You dont have enough information on the problem. The radio receives other signals fine? What is the frequency and mode?
6/14/2022 3:47:43 PM • Icom IC-718 Base... • Answered on Jun 14, 2022
0helpful
1answer

Model 718. Why is CW mode kaput?

There are a few possible reasons why your radio might not be transmitting in CW mode. One possibility is that the keyer chip has gone bad. Another possibility is that there is a problem with the power supply. If you have a multimeter, you can check the voltages to see if they are within specification. Finally, it's also possible that there is something wrong with the antenna connection. Make sure that everything is securely connected and that there are no loose wires. I hope this helps!
4/23/2022 4:24:33 PM • Icom Radio... • Answered on Apr 23, 2022
0helpful
1answer

Why won't my Icom AT-180 automatic antenna tuner tune at 21 or 18 mHz? Won't settle down and stop at low SWR.

Hi om sounds like you may have a break or something making that ant go haywire, have you checked all the line to see if there may be connection problem.another thing could you try the ant direct with a matcher inbetween to eliminate the auto tuner from circiut. This would narrow the fault down, have fun
3/26/2022 9:45:37 PM • Icom Radio... • Answered on Mar 26, 2022
0helpful
1answer

Icom m36 will not receive. Speaker makes noise

You may have the CTCSS tone squelch enabled so unless a station you're listening to is encoding CTCSS tones, you won't hear the traffic you're expecting.
2/28/2022 2:14:45 AM • Icom IC-M36 VHF... • Answered on Feb 28, 2022
0helpful
1answer

I forget my e880 password. Please tell me reset code.

unfortunately this is going to require a full factory default reset. so dial through everything and write your settings down. http://www.icom.co.jp/world/support/download/manual/pdf/ID-E880_0b.pdf
6/8/2021 12:01:42 PM • Icom ID-E880... • Answered on Jun 08, 2021
0helpful
1answer

Resetear icom ic f24

Tienes que usar un programador y un software. si necesitas el software me avisas. tienes el programador?
5/6/2021 4:36:33 PM • Icom Ic-f14 /... • Answered on May 06, 2021
0helpful
1answer

Need icom software CS-F1000S and icom ic-f5023 v3.4 for downloading

Contact Icom to inquire.
2/11/2021 2:09:49 PM • Icom Radio... • Answered on Feb 11, 2021
0helpful
1answer

Need icom IC-F3003 Programming software

Contact Icom directly to inquire.
2/11/2021 2:02:17 PM • Icom Radio... • Answered on Feb 11, 2021
0helpful
2answers

IC-A210

I can to see on Panel Screen ICOM IC-A210 message RX error
1/9/2021 4:22:02 PM • Icom IC-A210 VHF... • Answered on Jan 09, 2021
0helpful
2answers

Very low volume

Have done more research on this, and made some tests. I found the Ext Speaker jack sometimes did not make good contact when the earphone plug was removed, and cleaned/lubed the jack ... the entire unit must be disassembled for this, as the jack is mounted on the third circuit board which is soldered to the antenna jack and a ground shield in several places.

Audio output to an external speaker, whether connected to the earphone jack or directly to the main speaker contacts, is the same. An unpowered external speaker (4-inch audio speaker was used) has quite satisfactory volume. The internal speaker audio works, but seems distorted - I'll try to find a replacement.
9/29/2020 8:15:21 AM • Icom IC-R10... • Answered on Sep 29, 2020
0helpful
1answer

Can I use an Icom AT-180 ATU with my ICOM IC-7300 HF radio

AT-180 ATU is not intended for IC-7300. Icom IC-7300 have a built-in tuner already. maybe you can use a special cable or interface to use the AT-180 on IC-7300.
4/21/2020 9:24:26 PM • Icom Radio... • Answered on Apr 21, 2020
0helpful
1answer

(Newbie here) My icom IC-V8 turns on but doesnt beep or produce anysound when i change frequency. I tried resetting it but still no change..what should i do?

Look at pages 16 to 20 in the user manual. This may give you some insight as to haw this may occur. Also, A google search for this radio brings up a lot of useful info. This is a complicated radio as is indicated by the 80 page user manual. It's not one that you can pick up and use right out of the box!
11/10/2019 3:16:38 PM • Icom Radio... • Answered on Nov 10, 2019
0helpful
1answer

I want to know how to do hard reset on the ICOM IC-M802. Thanks.

The link below should help you. Lots of info in the service manual. It's intended to let someone rebuild the radio from the ground up.
11/10/2019 3:10:14 PM • Icom Radio... • Answered on Nov 10, 2019
0helpful
1answer

How to fix or troubleshoot icom v68 with low volume?

Try using an external speaker and see if you have the correct volume level. Radio speakers fail often, especially when used at high volume. The simple fix is to replace the speaker. It is seldom for the audio amplifier to fail this way. Usually they work or they don't.
11/10/2019 3:04:38 PM • Icom Radio... • Answered on Nov 10, 2019
0helpful
1answer

Icom M700pro. The S/FR Meter, 8 bar graph is always on.Does not move in receiving and transmitting. I reset the CPU , no difference. Anybody know why? thanks Harald

Try adjusting your RF gain control. This will often cause this to happen if it is fully on.
11/10/2019 3:02:35 PM • Icom Radio... • Answered on Nov 10, 2019
Not finding what you are looking for?
Icom Logo

388 questions posted

Ask a Question

Usually answered in minutes!

Top Icom Radio Communications Experts

Steve

Level 3 Expert

3290 Answers

Ngoro

Level 3 Expert

3508 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you an Icom Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...