Hyundai Electronics Televison & Video - Answered Questions & Fixed Issues

p1014ap06

1st resolder inverter board, if the problem still exist chek the flex cable.

chek power inverter board. and find inverter driver

The cost will reach to 2/3rd of the total cost of the device.

Press and hols the Volume Dn button on the front panel of the TV and display button on the remote control at the same time for about 5 seconds. If you wish to know more procedures to enter service mode to Hyundai TVs, check this link.

You have bad capacitors in your tv set that will need to be replaced.

is your lcd in english? what do you mean you ccant find indonesia on the menu? are you looking for the language or the indonesian channel? well if your looking for the language you should go the settings menu and go to language..from there try to find indonesia and enter,then the language will be indonesian..or if your wondering why you cant scan the channels on your lcd..you should try settings menu again and go to the channel set up..find auto scan and click it..then your lcd should be scanning and remembering all the channels thats been scanned,but before you do the scanning make sure that your antenna or your cable provider is connected to your tv..otherwise you wont scan anything

Hi.

It is not a lose wire. If problem was a lose wire or a bad solder joint it would have been sensible to vibration and the TV would have turned off when touched.

It is not a software problem either. The software cannot turn off the TV completely, at most the TV would freeze or go in standby.

If TV goes off completely, the problem is usually a defective PSU in rare situations a defective inverted can also give similar problems.

The problem is usually the PSU, A component (usually a capacitor starts failing) The other capacitors in PSU can compensate the work that is not being done by the defective part, and the PSU works for a while, until problem starts happening more often and TV does not turn on at all. In some case a defective inverter can do the same. In that case the inverter oscillator section is defective. The problem with the inverter is very uncommon.

Check the power supply. Sometimes it is possible to see at a glance a burnt spot or capacitors bulged on top. If there is nothing at a glance the PSU should be tested before replacing it.

PSU part number is PSCV121106B the PSU is not available anymore, the repair must be done replacing the parts on PSU. Below the repair kit with the components. For safety reasons the repair must be done by a trained person.

Here the repair kit: Repair Kit PSU PSCV1211068

Regards.

Ginko

You can get a 'Universal' remote from most electrical stores. You will need to get a set up code for your TV - try this site http://www.xdiv.com/remotes/

try turning DOWN the contrast &/or brightness. let me know if this works for you. Thsnks.
Dan.
[email protected]

If you have not gotten this resolved, follow the link below, it will help you out. The link will walk you through a power scan, which scans the codes on the tv until the correct one is found for the remote. If a code has not worked in the past, this will work much better. I hope it helps you.


http://www.dishnetwork.com/SupportSection/power-scan-instructions

Becki Barned
DISH Network Customer Service

I got the same problem, did you find a solution to this?

Andrew

Yes,Try website like Remotes.com to buy an exact orginal remote for the replacement.

see solution at: http://www.fixya.com/support/t1121498-hyundai_e320d_32_in_lcd_television_no
it may help. Sparky Jay

I had exactly the same problem with mine this week. After taking the back off and poking about with my multimeter (I am an electronics engineer!) I discovered that the power supply board is screwed to the chassis with 4 screws (three of which are system grounds(earth)). All three of the earthing point screws had worked their way loose - The fourth (top left as you look from the back) was still tight, but this one does not ground the board. After tightening these back up the television is now working fine again. - so fingers crossed! I will report back to this thread if it stops again! Please post here if you have the same fault and it does or doesn't fix it. Sparky Jay

try charles hyde and son web site (CHS) or amazon if still got old remote will need model number
if not can find with tv make and model number

Your best bet is to take the numbers off the inverter board and google those numbers. Hyundai does not make a set to my knowledge. A lot of sets are what we call a Heinz 57 set. They can have any number of manufacturers boards in them.

It is your "vergin media box" outputting a blue screen!
When this TV has no input it displays a msg box "No Input Signal" or "Signal out of Range" (PC video resolution is not correct.)

by replacing the memory . thanks anyway.

you must clean your remote inside & out