Husqvarna Logo

Husqvarna Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 983 Products
  • 77K Answers
  • 2M Views

https://www.youtube.com/watch?v=SxkR2Hade9M

This shows on a cud cadet but it is basically the same.

Husqvarna Garden | Answered on May 27, 2020


Likely top thread tension needs to be set higher.

With the additional layers it will take a higher top thread tension so the take up lever pulls the extra top thread from bottom side through the fabric stack before it takes it from the spool.

If youre not sure whether top or bottom thread that is nesting, try a different color top thread to make determination easier.

Husqvarna Sewing... | Answered on May 24, 2020


It could be the starter. Hook up a voltage meter to the wire that is on the starter. Try to start it. Watch the meter when it clicks. Does the voltage stay at 12 volts? If it does and the startter does not spin, then hit the starter to see if that helps. If you loose power then check the electrical connections on the battery. There are safety switches on the seat, blade engaugement lever and park / clutch lever.

https://www.youtube.com/watch?v=A8m88LawN0I

Husqvarna Garden | Answered on May 22, 2020


Where can I buy a dongel and emb card for my Scandinavia 400?

Thank you for your help
Ruth
[email protected]

Husqvarna Viking... | Answered on May 16, 2020


The decompression button for easy start?... absolutely.

Spray with carbureror cleaner and push/pull the button and try to get it to seal. Check or remove the spark arrestor screen.

Spray a short burst starter fluid down carburetor throat and promptly start. It should fire and run for a couple seconds. If if fires then likely just no fuel through carbureror.

Husqvarna Garden | Answered on May 15, 2020


I too, have the same problem withmy Designer 1. I just bought ISACORD brand polyester embroidery thread to hopefully solve this problem, but I believe it must be a tension problem. I have a "date" with the repair lady on Friday (11/22/08) and if it gets repaired I will re-post what the problem was. Still love the machine WHEN IT SEWS!!

Husqvarna... | Answered on May 15, 2020


https://www.lawnmowerforum.com/threads/is-there-a-best-tire-pressure.31615/

This forum has good information of the correct/best pressure fot the tires.

Husqvarna 26 Hp... | Answered on May 12, 2020


There could be several different problems. The oem wheel has metal bushings that can wear. They are replaceable. New rims will have them in. You can also get new rims with sealed bearings which fit tighter on the spindles. Spindles can also wear causing looseness in the tires. Replace them if they are bad.

Husqvarna Garden | Answered on May 12, 2020


Suggest that it be serviced by an authorized Husqvarna Viking Dealer. You can find the nearest dealer by click on the "Dealer" link at http://www.husqvarnaviking.com
Good luck.

Husqvarna Viking... | Answered on May 11, 2020


Seat must be occupied if brake off and PTO on.

See wiring diagram
https://www.jackssmallengines.com/jacks-parts-lookup/manufacturer/husqvarna/ride-mower-turf-care/z-4217-bia-968999280-2005-08/wiring-schematic

Husqvarna Garden | Answered on May 09, 2020


Take the foot pedal apart and look for a return spring. Clean the inside track at the same time. You will probably find the screws hidden under the rubber feet.

Husqvarna Sewing... | Answered on May 07, 2020


WHY DO YOU NOT CALL THE PLACE YOU BOUGHT IT FROM AND GET HUFFY WITH THEM SURELY YOU HAVE WARRANTY

Husqvarna Sewing... | Answered on May 02, 2020

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Mike

Level 3 Expert

4369 Answers

ray gallant

Level 3 Expert

67926 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...