HP Televison & Video - Recent Questions, Troubleshooting & Support

All HP iq77x all-in-one PCs suffer from the same problem of a faulty motherboard. This is primarily a soldering issue on the graphics chip,which develops cracks in the solder balls. The PCs contained a separate graphics card, which goes faulty first. This can be removed and the display connector can be moved on the motherboard to use the on-board graphics. This will eventually show the same issue. A short term fix was to heat the graphics chip with a hot air gun or other means (plenty of suggestions can be found on-line) which sometimes works for a few weeks at most. The only 'permanent' fix is to have the chip professionally removed and re-soldered; an expensive option.
If you are lucky, your PC is still wired to use the add-on graphics card, in which case you might be able to remove this and rewire for the motherboard graphics.

HP Televison &... | Answered on Mar 21, 2019

look on your f buttons f5 on mine

HP Televison &... | Answered on Mar 21, 2019

Sounds like The main power supply regulator section circuit fault. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
Search the site by type in the "brand name" to your device; [Exclude the model number], in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. See the site by a desktop. Mobile view has no search box. If you are viewing it by your mobile, see it in webview./

HP Televison &... | Answered on Nov 08, 2018


Here is the solution.Below are some of the popular games and programs downloading sites for mobiles
  • http://www.mobileheart.com/cell-phone-softwares/1612-Samsung-D980-Software.aspx

  • http://www.youpark.com/samsung/samsung-d980/mobile-applications/

  • http://www.getjar.com/mobile-all-applications-for-samsung-sgh-d980/

  • http://gallery.mobile9.com/c/samsung-d980-java-softwares_1934/1/
Hope this helps...

HP (L1766A)... | Answered on Oct 24, 2018

The tuner might be too old. I have a sony tuner card that does not function with windows 7.

HP Hauppauge... | Answered on Jul 24, 2018

The first thing to do is go into the device manager and delete the drivers for the display and let windows reinstall them. It may be a bad or out of date driver. So when you restart the computer it will put the driver back. Since you did not post the operating system, there is not a lot more I can tell you. If this does not help, you can try an external monitor to see if the problem is present there. If it is then it may be a display chipset issue.

HP Televison &... | Answered on Jul 15, 2018

hi it sounds like your plasma has gone in stand by mode look on youtube will tell you all about stand by type in how to fix and tv make model stuck in stand by more than likely capacitors blown if your not any good soldering boards id phone tv guy out but if you are then youtube it hope this hopes

HP PL5060N 50... | Answered on Mar 04, 2018

Do a reset to this TV, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts.
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

HP PL5060N 50... | Answered on Feb 20, 2018

What is a grlyb-0311 ??

HP Televison &... | Answered on Feb 08, 2018

you cannot connect them an all in one computer does not support a separate monitor

HP Televison &... | Answered on Jan 26, 2018

If those bars are vertical are going up and down and not horizontal that means the lower circuit board that connect to the plasma panel are bad most likely this is an LG TV but this is not something that can be fixed you can take it apart while at least an hour after it's unplugged before you can touch ID cards along the long circuit board see if there's any connection connection connection that you can disconnect and reconnect and very carefully clean up possibly this could be the problem but usually when you have that type of line which is a vertical line you have a bad panel and that's not good and I'm betting this is an LG TV

HP Televison &... | Answered on Jan 26, 2018

Not finding what you are looking for?
HP Logo

907 questions posted

Ask a Question

Usually answered in minutes!

Top HP Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76416 Answers


Level 2 Expert

176 Answers

Stan Ford

Level 3 Expert

2910 Answers

Are you a HP Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides