Hayward Garden - Recent Questions, Troubleshooting & Support

One of my well-known company Akshar Technologies working in Same fields related to the Fire Fighting Equipment and fire hydrant system so you contact them and get better advise and answer.

Hayward Sand... | Answered on Jan 16, 2018

contact pump manufacturers as they have charts that when your information is put in to the chart will show a minimum power input required to do the jib

Hayward Sand... | Answered on Jun 22, 2017

hi can anyone help me my blow vac wont suck up it blows out but no suction what do i do.

Hayward 1.0 HP... | Answered on Nov 30, 2016

when you go to ask.com [www.ask.com/]
your link or information you are requesting is to long, you need key words. i was show you a sample.
try this one


here are some sites that may help you.
heres another idea look for the serial #. find out what city, state, zip-code if there, name of manufacture and try locating the old business or find out if the have went in to business with another company or changed there name.

good luck rod

Hayward S220t... | Answered on Sep 16, 2015

Good day, this is John the Hayward tech. I have given you a link to the Power Flo II owners guide. You will need to remove the screws on the front of the black plastic housing to access the impeller. Holding the shaft of the motor you will need to turn the impeller CC to remove. Once removed you will need to remove the four motor through bolts that both hold the motor together and hold the housing to the motor. Take a look at the manual parts breakdown. Strongly recommend letting a dealer perform this procedure. Always replace all gasgets and seals. http://www.hayward-pool.com/pdf/manuals/PowerFloLXandPowerFloII.pdf

Hayward 1.0 HP... | Answered on Apr 02, 2015

Good Day, this is John the Hayward tech. I have attached a link to the SP-1070 skimmer. The weir is replaced by removing a screw from inside the front of the throat of the skimmer. This removes the plate the weir is attached to. You can also just pop out the weir without removing this plate by gently bending the plate at one end and removing the weir pins from the plate. http://www.hayward-pool.com/pdf/manuals/Automatic-Surface-Skimmer-SP1071-SP1070.pdf

Hayward SP1070... | Answered on Sep 03, 2014

Pump Size Calculation: Gauging the correct size for your water garden pump will ensure your pond receives the proper water circulation. Unless the pump you buy is already configured with a built-in fountain head, you'll need to calculate how much a pump can handle before you choose a certain size or model. A good rule of thumb is that pumps should be able to pump out about half the pond volume every hour. So a pump that moves 500 gallons per hour would be appropriate for a 1,000 gallon pond. In order to determine the size pump you'll need, you must calculate several key measurements.

Hayward Sand... | Answered on Oct 02, 2011

from the Hayward support site....

Why is my pump cutting off and on every 5-10 seconds?
  • Hayward motors are factory wired for 240 volts unless the motor is 120 volts ONLY. Check the voltage of the incoming supply power and ensure the motor is wired or can be wired for this voltage (data plate on motor will help provide voltage and wiring information). Also check for loose or badly connected wires. Contact a certified electrician for repair.

Hayward Heatpro... | Answered on Sep 09, 2011

Not finding what you are looking for?
Hayward Logo

84 questions posted

Ask a Question

Usually answered in minutes!

Top Hayward Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

john h

Level 3 Expert

23515 Answers


Level 3 Expert

85239 Answers

Are you a Hayward Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides