Hayward Logo

Hayward Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 313 Products
  • 14K Answers
  • 493K Views

Call a qualified electrician. More information would be needed to accurately trouble shoot your issue. Do you have automation connected to your heater? Is the heater trying to fire when the pump is off or is it ONLY the fan?
Try disconnecting your Water Pressure switch on the heater and see if the issue stops. With WP switch disconnected the heater should not work and the fan should stay off. Replace WP switch and see what happens.
Call a QUALIFIED electrician.

Hayward Pool &... | Answered on Aug 12, 2019


Check for proper supply voltage and that the impeller moves freely. If these are good then likely a bad capacitor.

Hayward Pool &... | Answered on Jul 30, 2019


the prologic control unit will not offer programming for what you seek. the most detailed timers will offer weekday or weekend for each pump speed. you may want to get a remote system so you can control functions from your smartphone

Hayward Pool &... | Answered on Jul 26, 2019


i always start a new filter in backwash mode. that way, any dust will be washed away and not into the swimming pool

Hayward SAND... | Answered on Jul 26, 2019


from what i can find, it will take 350lbs of sand. there should be a chart on the actual filter housing

Hayward SAND... | Answered on Jul 26, 2019


no description of issue. good luck

Hayward H Series... | Answered on Jul 26, 2019


try filling your hose by holding it in front of the return jet. once filled, hook the hose up as normal

Hayward Pool &... | Answered on Jul 26, 2019


put the housing on the base (level) and make sure the three 'locators' on the bottom of filter housing are resting inside the base ring. put the standpipe into the housing and install the 8 laterals. make sure the standpipe is straight and centred in the housing (i use duct tape to block the top of the standpipe and secure the standpipe to the housing. fill the housing roughly halfway with water. slowly pour sand into the housing making sure to keep the standpipe centred. once you have installed the correct amount of sand, install the dial valve and secure it with the supplied clamping system.

Hayward SAND... | Answered on Jul 26, 2019


pool manuals are available on amazon

Hayward SAND... | Answered on Jul 26, 2019


make sure your filter is clean. put it on bypass if possible to see if that is where the restriction is.
it is also possible that some debris has found its way into the impeller and reducing the pump efficiency. unplug the pump and put your finger into the wet end of the pump (remove basket first). if you can feel leaves or twigs, then you will have to open the pump and clean the impeller

Hayward Power... | Answered on Jul 26, 2019


there are several causes of a bD code on hayward heaters. because of this, i have included the link to the code page so you can eliminate and review them.
https://hayward-pool-assets.com/assets/documents/poolscanada/pdf/manuals/universal-h-series-owners-manual.pdf?fromCDN=true

Hayward H400fdp... | Answered on Jul 26, 2019


there is no error code 60 in the world of hayward. is there any chance you are seeing bO? if so, that stands for bypass on and the heater is being controlled by a remote controller.

Hayward H-series... | Answered on Jul 26, 2019


this is a common issue. there is a componant on the circuit board called a voltage limiter. when there are power surges (by hydro company or by using a timer), this capacitor takes the surge to protect the circuit board. in your case, the limiter has blown.
you can either replace the circuit board or find someone to remove the limiter and solder in a new one. (its the round black disc to the right of the front display toward the top) in most cases, you will see a hairline crack in the casing or it may have exploded completely. i usually tap it with a screw driver to show customers the damage. FYI: i usually replace about 50 a year and never had one fail

Hayward Pool &... | Answered on Jul 26, 2019


the rinse setting only cleans out the dirty water in freeboard and pushes sand to pack it. just about impossible for it to not work. if there is water coming out the discharge, you are golden.

Hayward Pool &... | Answered on Jul 26, 2019


there is a relay on the back of the main circuit board that has separated from the circuit. you can resolder this relay quite easily by removing the board.
DANGER: be sure to cut the power to the control box at the main breaker. turning off the breakers in the hayward box will NOT eliminate the power

Hayward Pool &... | Answered on Jul 26, 2019


i find the aqua rite systems to be very helpful in diagnosing problems. if you can describe the problem you are having, i may be able to help

Hayward Pool &... | Answered on Jul 26, 2019


As far as I know, refrigerant is not used in the heating of pools and spas. Sounds like it is just a connection leak and can be fixed by redoing the joint connection.

Hayward Pool &... | Answered on Jul 25, 2019


Check to make sure that there is enough water in the pool and that the weir door in the skimmer box isn't jammed in the upright position

Hayward Pool &... | Answered on Jul 16, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Hayward Experts

john h

Level 3 Expert

23515 Answers

Fahr Quad

Level 3 Expert

774 Answers

Bill Boyd

Level 3 Expert

53816 Answers

Are you a Hayward Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...