Hannspree Televison & Video - Answered Questions & Fixed Issues

The weight of the Hannspree HSG1074 24 inch LCD HDTV is approximately 8.8 pounds (4 kg) without the stand. However, the weight may vary slightly depending on the specific model and any additional accessories that are included with the TV. If you need more precise information, you may be able to find the weight listed on the product specifications page on the Hannspree website or in the user manual that came with the TV.

The issue you are experiencing with your Hannspree 42 LCD TV could be caused by a few different things, such as a loose cable connection, a faulty T-con board, or a defective panel. Here are a few steps you can try to troubleshoot the issue:

1. Check the cable connections: Make sure that all the cables connected to your TV, especially the ones connected to the right side of the TV, are firmly plugged in.
2. Power reset: Try turning off your TV and unplugging it from the power outlet for at least 10-15 minutes, then plug it back in and turn it on again.
3. Swap inputs: If you are only experiencing the ghosting on one input, try swapping the input with another one to see if the issue persists.
4. T-con board: If none of the above steps resolve the issue, it is possible that the T-con board is faulty. The T-con board controls the timing of the image displayed on the screen and is often the culprit of ghosting issues. A technician can diagnose and replace this board if necessary.
5. Panel: If the above steps don't resolve the issue, it is possible that the LCD panel itself is defective. This is less common but can happen over time. Unfortunately, replacing the panel can be costly and may not be worth it on an older TV.

If none of the above steps resolve the issue, it may be best to contact a qualified technician to diagnose and repair the issue.

To program a Hannspree remote to a Hannspree TV, first turn on the TV and then press and hold the "Code" button on the remote until the LED light turns on. Next, enter the four-digit code for the TV using the number keys on the remote. If the TV turns off, press the "Code" button to save the code. If it doesn't turn off, try another code until you find one that works. If you cannot find the four-digit code for your Hannspree TV, you can try using the code search feature on the remote. To do this, follow the steps for programming the remote but instead of entering a code, press and release the "Code" button and then press the "Power" button repeatedly until the TV turns off. Then, press the "Code" button to save the code. If you are having trouble programming the remote, make sure you are aiming the remote directly at the TV and that you are not too far away. Also, check that the batteries in the remote are fresh and properly installed. If you accidentally program the remote to the wrong TV or if you want to program it to a different TV, you can reset the remote to its default settings by pressing and holding the "Code" button for at least three seconds until the LED light turns off. This will erase any previously programmed codes.

Question moved from Cellphones. It is broken, but try a power reset. Disconnect the mains power at the wall outlet for 5 minutes. https://www.fixya.com/support/r29790007-repairing_own_television ..

Normally the HDMI cable input for your Cable set top box. They are numbered. However, you can just scroll through until the picture appears.

It is not compatible. The 42" requires upscalling and the 19" hasn't got upscalling.

check the batteries in remote .

To do a factory reset, you have to enter its Service Mode. If you wish to get some details; check the sites linked here. https://elektrotricks.blogspot.com/ https://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done. NB: Please read and understand well, the instructions to enter the service mode, before you begin. Be very careful. Note how to "EXIT" the service mode; after entering and adjusting data. This is very important Search the site by type in the Brand Name of your set, in its search bar at the right side column, and press enter. See it in by Webview with mobile or by desktop. Mobile View has no search box.

Sounds like system memory fault. Contact any service technician to make it sure. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/

Might be one of two things. Check if there is any damage to screen if not the video curcit is bad

http://translate.google.com Secret service menu Hannspree HSG1113 https://electronicshelponline.blogspot.com/2015/03/hannspree-lcd-tv-how-to-enter-service.html Possible menu - Quoting from link above: SERVICE MODE [Hanspree AT06 42" LCD TV] (Horizontal Frequency 31.5KHz to 48KHz) * In the TV mode, adjust volume to Zero and press number keys 9 > 8 > 7 > 6 to enter service mode. * To exit, press the EXIT button on the remote control. SERVICE MODE (Hanhspree GT02 32E - GT03-37E1) 1 Switch on the LCD TV . 2 Press 9-9-1 on the remote control to enter the internal Service menu. 3 Press MENU to switch the service mode pages. 4 Press ?? to scroll through the various menu options. 5 Press ?? to change the menu settings. 6 Press MENUto save the new settings and switch to next page and press EXITto exit from service mode to normal mode. TV / AV / S-VIDEO / WHITE BALANCE / BRIGHTNESS & CONTRAST ADJUSTMENTS WHITE BALANCE ADJUSTMENT 1 Press 991 on the remote control to enter the internal Service menu. 2 Press MENU to switch to the PW106 Scaler Menu page 3 Press ?? to scroll to Page 2-3 options 4 Press ?? to adjust the Offset Red, Offset Blue, Gain Red, Gain Blue menu settings. 5 Press EXIT to save the new settings and exit. [Don't adjust others setting in page 2-3] Click on the Pictures to Zoom In BRIGHTNESS ADJUSTMENT 1 Repeat the above mentioned step 1 to 2 2 Press ?? to scroll to PW106 FE VDC Menu Page 2-1 options 3 Press ?? adjust the Brightness setting. 4 Press ?? to scroll to TV/AV/S Parameter=AV1 setting and pressuto run the setting. (This procedure will copy the settings of AV1 to S & TV) ATSC DTV WHITE BALANCE / BRIGHTNESS / CONTRAST ADJUSTMENT 1 Repeat the above mentioned step 1 to 2 2 Press ?? to scroll to PW106 Scaler Menu Page 2-3 options 3 Press ?,? to adjust the Offset Red, Offset Blue, Gain Red, Gain Blue menu settings 4 Press to save the new settings and exit. [Don't adjust others settings in page 2-3] YCbCr & YpbPr of COMPONENT 1, 2 WHITE BALANCE/BRIGHTNESS/CONTRAST ADJUSTMENT Getting COMPONENT-1 connect to 1080i signal. (The settings could not be saved if signals input from COMPONENT 2 or connect to other sources such as 720P, 480P, 480i,etc. WHITE BALANCE ADJUSTMENT OF Component 1] Repeat the above mentioned step 1 to 2 2] Press ?? to scroll to PE106 FE ADC page 2-3 options 3] Press ?? to adjust the Offset Red and Off Blue settings. 4] Press ??to adjust the Offset Green setting. 5] Press ?? to adjust the Gain Green setting. 6] Press ?? to scroll to 480i/480P/720P Parameter=1080i setting and press ? to run the setting. (This procedure will copy the setting of 1080i to 480i/480P/720P) 7] Press EXIT to save the new settings and exit. WHITE BALANCE ADJUSTMENT OF PC INPUT 1.Connecting to VGA Timing mode 2.Under service mode, Press ?? to scroll to PE106 FE ADC page 2-2 options 3.Press ?? to adjust the Offset Red, Offset Green and Off Blue settings. 4.Press ?? to adjust the Gain Red and Gain Blue settings. 5.Press EXIT to save the new settings and exit.

Hello, Mike - Hannspree North America: 888-808-6789 ( Mon - Fri: 8:00am to 5:00pm (Eastern Time) Source: http://www.hannspree.com/US/EN/ContactUs.aspx Hannspree Europe See: http://www.hannspree.eu/en/about-hannspree/contact-us Germany, France, Italy, United Kingdom, Spain & Portugal Best wishes.

Europe or the USA - different phone numbers. https://www.google.com/search?q=HANNSPREE+TV+HELP+PHONE+NUMBER&ie=utf-8&oe=utf-8&client=firefox-b-1-ab

Last page of this free monitor has the corporate phone numbers in many countries you could call for manual. Link below is for a monitor and not a tv, but note the phone numbers and email addresses. http://office.manualsonline.com/manuals/mfg/hannspree/xm_1.html

Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

I would get the TV replaced under guarantee. There maybe a loose wire in the power supply or invertor stages that is arcing and burning

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily. http://homenol.blogspot.com/ http://remotesearch.blogspot.com/ http://electronicshelponline.blogspot.com/ http://electrohelponline.blogspot.com/ Programming Notes • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote. • Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality. This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.

Unplug the television from mains first take the batteries out the remote then plug the tele back and switch on from the television see what happens if it goes back to normal the you have the volume bottons jammed on your remote control

Do a factory reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Main system control memory IC fault. This is a very small IC; have 8 solder terminals, and can be located very near to the main system control-chroma IC. Check and replace it. Be sure to replace it with the same number printed on it; in all respect. Otherwise, it won't go. http://electronicshelponline.blogspot.com/ Before replacing it, try a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here.