Haier Washing Machines - Recent Questions, Troubleshooting & Support


I have a Haier HLP21N that had the same problem. Three blinking lights and refused to spin. It turns out the issue was the lid. The left side plastic hinge had broken the week before. What I didn't realize is that when the lid closes, that back hinge pushes up a rod which tells the machine that the lid is closed and it's safe to spin. So check that hinge and if it is broken you will either need to order a new lid or find some material to stuff under the hinge so that it stays up. I chose the latter option. Just know that going the DIY route means that your machine will continue to spin if you open the lid going forward!

Haier HLP21E Top... | Answered on Apr 30, 2020


under agitator check cogs and spline to drum if ok bad bearings

Haier Washing... | Answered on Apr 16, 2020


if motor works check belt if ok check under agitator for bad cogs or spline to drum

Haier Washing... | Answered on Apr 16, 2020


Washer will not drain:
Thedrain water pumpis the main part in your washing machine that pumps out the water. If this is defective or has failed in any way, this will be the reason why your washer will not drain the water. Before you order a new drain pump, make sure tocheck the pump to be sure a small object like clothing or similar has not lodged itself insideof it causing the NO DRAIN issue and even a no spin issue?. If the drain pump is not clogged, you can test it with a multimeter and remove and replace if needed.

Read more: http://removeandreplace.com/2014/10/30/fix-washing-machine-that-wont-drain-washer-not-draining-water/#ixzz3X2LbXMWJ
The washing machinedrain hoseis where the water flows through to get the water out.If this drain hose is blocked, kinked, bent, or clogged, the washer will NOT be able to remove the waterfrom the tub. Check the drain hose to be sure it allows the water to flow freely. You can take the drain hose off and run water through it in your sink to be sure it is not blocked. If there is water STILL in the washer when you remove the drain hose, grab a bucket as the water will exit from where you disconnected it Thewater pump belt(to drain out the water) may have broke or become frayed or loose.If this belt breaks then it is unable to drain and remove the water from your washer. Inspect the belt to see if this is causing theNO DRAINissue and remove and replace if needed.

If thelid switchis not working as required it will cause your washer to not drain (and many other problems).This may be unlikely as a bad lid switch will usually cause your washer to alsonot agitate or spin.However on some models this can vary. The best thing to do if you have a suspected bad lid switch is to test it. It can fail electrically and or mechanically. If mechanical failure is the issue, you should be able to see if it is cracked, broken, or not in place to make contact with the lid. To test it electrically, use a multimeter set on Ohms and test it for continuityMy advice is free cuz God is good!


water pump clogged washer 2-undefined-undefined-0_1.jpg

water pump belt broken104-undefined-undefined-2.jpg

water pump sump dirty-undefined-undefined-5_1.jpg

water pump belt broken104-undefined-undefined-9.jpg

Haier Washing... | Answered on Mar 19, 2020


Drain hose is blocked or twisted. ... Ensure the highest part of the drain hose is nearest the washing machine. Check the waste water pipes in the building are clear of any obstructions and flow freely. If the error is still exist, please unplug the machine and close the water tap, then call for service.Mar 13, 2014

Error Code-control panel display "Err2" (Error 2, Error2 ... - Haier


https://www.haier.com > faq > washing_machine > front_loading > question

Videos

https://www.google.com/search?q=haier+washing+machine+error+code+e2

Haier Washing... | Answered on Dec 08, 2019


GOOGLE HAIER ERROR CODES

Haier Washing... | Answered on Nov 26, 2019


try running a minimum load with light clothes. If it still does it, look for something broken that holds the tub in place, maybe a spring.

Haier Washing... | Answered on Nov 07, 2019


Dismantle the pipe fixing. Clean and use a little washing up liquid when re fitting.

Haier Washing... | Answered on Nov 03, 2019


Two possible causes. Try cleaning the fabric softener residue off of the temperature/moisture sensor. The other cause could be the thermostat has failed.

Haier HLP21E Top... | Answered on Oct 23, 2019


This could be anything from a faulty water valve , machine not draining , faulty electronic board , faulty timer unit ...For the machine to continue it must complete its last cycle . Any fault codes showing ?, was it filling , was it draining properly ??, please contact your registered whiteware technician for proper fault diagnosys , cheers .

Haier Washing... | Answered on Aug 08, 2019


If its a top loader, most machine s have a dispenser on the top panel or somewhere in the top of the splash guard of the tub. On a front loader.... I have never seen a bleach dispenser on any of them.

Haier Washing... | Answered on Jun 17, 2019

Not finding what you are looking for?
Haier Logo

1,127 questions posted

Ask a Question

Usually answered in minutes!

Top Haier Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6099 Answers

Are you a Haier Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...