Gestetner Office Equipment & Supplies - Recent Questions, Troubleshooting & Support

0helpful
1answer

How would I identify faulty fault sensors in gestetner MP2501L copier and replace them?

You can't. As I said you need the service engineer with the laptop. These Office Machines are NOT consumer serviceable. They hook up the laptop with the Ricoh software and it interrogates the computer, the mainboard and everything on it. The error message you get is from the brains inside it..Original question and answerhttps://www.fixya.com/support/t29802178-am_posting_again_stripped_off_gestetner..
1/15/2021 4:04:21 AM • Gestetner Office... • Answered on Jan 15, 2021
0helpful
1answer

Am posting again. I stripped off gestetner MP2501L 8 times due to problem ' see instructions on right side to solve' but same. No paper inside. What is the actual problem.

Hello Christopher Are you in the Philippines? I notice that your copier has changed from Ricoh to Gestetner? We are a North American website. This is a commercial office machine, and from my experience of them is that on the right side you will see on the inside, a list of instructions for where to check for obstructions. It seems you have already done this 8 times! Frustrating! Try this; Open the right side cover, unlatch all the bits at that side. Open the straight pass door on the left side. remove ALL the paper drawers. Get a powerful flashlight, look in all the spaces you have just created, especially at the edges of drawers and paper pathways. You are looking for a tiny piece of paper that one of your employees carelessly left behind after a paper jam.The one I found was right at the back of the straight pass door. When a sensor is covered, it creates that message. If that fails, Ricoh will have to come and attach their Laptop scan software to it which will tell which sensor is obstructed or has failed.
1/14/2021 4:54:33 PM • Gestetner Office... • Answered on Jan 14, 2021
0helpful
1answer

Gestetner DX2430 error code E-00

Clamper error The MPU cannot detect the clamper position sensor signal ( open or closed) within 3.0 seconds after the clamper
12/2/2019 1:38:38 PM • Gestetner Office... • Answered on Dec 02, 2019
0answers

E-24

Be the first to answer 6/17/2019 10:46:02 AM • Gestetner -... • Posted on Jun 17, 2019Be the first to answer
0helpful
1answer

Error code E-01 for gestetner dx 2430

i m gatting a E-00 error code geststner dx2430
6/4/2019 7:30:53 AM • Gestetner Office... • Answered on Jun 04, 2019
0helpful
1answer

Sc 569 for ricoh mp 5500

sc 569 is the pressure roller contact sensor error Troubleshooting Procedures: 1. Check or replace the harness of the pressure roller contact sensor. 2. Replace the pressure roller contact sensor. 3. Replace the pressure roller contact motor
6/2/2019 2:54:43 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

SC 569 Error code in MP 5500

sc 569 is the pressure roller contact sensor error Troubleshooting Procedures: 1. Check or replace the harness of the pressure roller contact sensor. 2. Replace the pressure roller contact sensor. 3. Replace the pressure roller contact motor
6/2/2019 2:49:55 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

How to reset gestetner sp 8100dn aficio error sc547 power off on ?

Sc 547 is Zero cross error Troubleshooting : 1. Check the power supply source. 2. Replace the +24V fuse on the PSU. 3. Replace the PSU ( power supply unit)
6/2/2019 2:20:51 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

How to reset gestetner sp 8100dn aficio error sc547

Sc 547 is Zero cross error Troubleshooting : 1. Check the power supply source. 2. Replace the +24V fuse on the PSU. 3. Replace the PSU ( power supply unit)
6/2/2019 2:19:34 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

How do i remove password from a gestetner Aficio 2212?

password word can be reset in special SP mode as follows: Reset, 1,4,3 press C then hold C special SP mode, go to SP direct 5-846-046 This will rest the Admin password to default
6/2/2019 2:12:38 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

What remove password on a gestetner Aficio 2212 copier

password word can be reset in special SP mode as follows: Reset, 1,4,3 press C then hold C special SP mode, go to SP direct 5-846-046 This will rest the Admin password to default
6/2/2019 2:11:54 AM • Gestetner Office... • Answered on Jun 02, 2019
0helpful
1answer

Copies dosent come out

u didn't mention the model of your machine
6/1/2019 2:08:52 AM • Gestetner Dsm675... • Answered on Jun 01, 2019
0helpful
1answer

I have Gestetner DSM725 and the wrench light is lit with advice to call service Problem is lit as SC546; Can I correct it at home by re-setting machine ? This happened before and service told me to d

Sc 546 means Unstable fusing temperature Possible Cause : 1-Thermistor disconnected or defective 2-Fusing unit drawer installed Incorrectly To reset that code do this: Press the Clear Mode key. Use the keypad to enter "107". Hold down Clear/Stop for at least 3 seconds. Enter the Service Mode. Do sp 5810 (SC Code Reset )
6/1/2019 1:38:07 AM • Gestetner DSm725... • Answered on Jun 01, 2019
0helpful
1answer

Ink idling problem in gestetner dx 2330 copy printer

Hi Hope this helps.The metal gauze filter (see image) behind the input nipple on the drum unit may become blocked with congealed ink deposits causing the ink not to feed at full flow.Strip and clean the blocked gauze filter in the Ink Supply System.
4/29/2019 3:43:20 AM • Gestetner Office... • Answered on Apr 29, 2019
0helpful
1answer

What do you do when the color registration adjustment fails on a Gestetner C2500

The ID sensors are dirty or transfer belt unit is damaged/dirty/faulty. The ID sensors are below the fusing unit facing down onto the belt. Usually best to remove the fuser unit and the belt unit to get to them with a short brush or unscrew to remove them but be very careful not to damage the transfer belt!
4/15/2019 10:02:41 PM • Gestetner Office... • Answered on Apr 15, 2019
0helpful
2answers

Close the lower door while it was closed gestetner 1802 copier

Door switch not working
4/15/2019 9:55:53 PM • Gestetner Office... • Answered on Apr 15, 2019
0helpful
1answer

How can I solve E14 code on gestetner copy priter 5308

Clean paper exit feeders
4/15/2019 10:33:57 AM • Gestetner Office... • Answered on Apr 15, 2019
0helpful
1answer

Error code E-01 for gestetner dx 2430 - copy printer

Description. Cutter error The cutter HP sensor does not turn on within 3.0 seconds after the cutter motor turns on .
4/15/2019 10:32:48 AM • Gestetner Office... • Answered on Apr 15, 2019
Not finding what you are looking for?
Gestetner Logo

1,214 questions posted

Ask a Question

Usually answered in minutes!

Top Gestetner Office Equipment & Supplies Experts

OfficeServiceAjnc
OfficeServiceAjnc

Level 2 Expert

214 Answers

Morne Olivier
Morne Olivier

Level 2 Expert

264 Answers

Daniel Blask
Daniel Blask

Level 2 Expert

172 Answers

Are you a Gestetner Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...