GE Washing Machines - Recent Questions, Troubleshooting & Support

0helpful
1answer

GE Washer. How to replace the door latch please?

Question edited for clarity and CAPS, but no model number, top load or front load? ..
6/4/2024 11:26:37 PM • GE Washing... • Answered on Jun 04, 2024
0helpful
2answers

GE WSLP1100A0WW not agitating

It sounds like the clutch is slipping https://www.google.com/search?q=GE+WSLP1100A0WW+not+agitating

Top Load Washer - Fills But Will Not Agitate

GE Appliances https://products.geappliances.com > appliance > gea-sup... If the lid switch probe or magnet is missing or damaged, the washer will not agitate or spin, even with the lid closed. Missing: WSLP1100A0WW ‎' Show results with: WSLP1100A0WW

SOLVED: GE WSLP1100A0WW not agitating

Fixya https://www.fixya.com > ... > Washing Machines > GE 17 hours ago - Ge top loader washer agitator does not work To check the agitator. Start the washer into wash cycle. Once started Push down on top of agitator.

Ge Washing Machine - Washer Won't Spin Or Agitate

Repair Clinic https://www.repairclinic.com > RepairHelp > Ge-Washe... If a washer is not spinning or agitating, you should first determine if the drive motor is running and if power is reaching the drive motor. If no power if ... ..
4/21/2024 6:22:15 AM • GE Washing... • Answered on Apr 21, 2024
0helpful
1answer

Can I get new brushes for my GE handmixer 56M17

No there’s no brushes for GE handmixer
3/10/2024 8:12:40 PM • GE Washing... • Answered on Mar 10, 2024
0helpful
1answer

GE WASHER MODEL GFWH1200HOWW RUNNING EXTRAAA LONG ON WASH CYCLES??

Hello Heather Good to see you again. Also check the small strainers on the water connectors. They can block up with limescale and debris. While the connectors are off, turn on the water into a bucket or a sink. You should have a VERY powerful jet of water. Anything that will reduce flow will lengthen the fill time and therefore to total wash time due to fill and rinses. When it pumps out, also check you have good flow in the drain hose and items can jam in the ridges and catch lint enough to block them almost completely. One clever thing to do is whilst the water inlet connectors are off, unlock the drain hose, unhook the part that makes the hook, put the round connector in the hose and wrap a tea towel around it. Get someone to turn the water on full bore whilst you are gripping the two hoses together. Run it for a full minute. Water will be flushed into the machine through the pump in reverse. Put everything back and run a rinse and spin with nothing in it, look at all the black lint that is pumped out! I did that once at work and found an apple stalk that had lodged across the ridges of the drain hose which had 90% blocked the pipe. ..
2/23/2024 8:08:04 PM • GE Washing... • Answered on Feb 23, 2024
0helpful
2answers

The start button is flashing, but the wash cycle will not start, how do I fix this?

unplug you washing machine and wait for two minutes.then plug back your washing machine. before you press start button please see to it the the door panel is securely closed
1/7/2024 12:39:29 AM • GE GFWN1100LWW... • Answered on Jan 07, 2024
0helpful
2answers

Plastic tab on back of backsplash assembly that holds timer in place has cracked

Might be able to fix with a zip tie through drilled hole or holes.
1/4/2024 8:50:46 PM • GE GTWN3000MWS... • Answered on Jan 04, 2024
0helpful
2answers

Stripped connection at the cold water intake into washing machine

If your inlet valve itself is stripped then you have to replace the valve. The plastic thread is part of the inlet valve. If its only the screen in your inlet valve you can remove the screen and replace it. However if you crossthread anything plastic it HAS to be replaced.

If you give me your model number of the washer usually the wpl 4318046 can be used as an inlet valve which is a cheaper alternative than your local parts distributor would tell you. GE parts on avg are 30% more expensive than anything else. On ANY ge appliance there is usually a way around there replacements with some minor altercations. I wish this site had a way you could contact me directly. I just joined so am not an expert yet but ive done my time in the field. If i could give you any expert advise its DONT BUY GE, OR LG.

Let me know if this helps.
12/11/2023 6:33:13 PM • GE Washing... • Answered on Dec 11, 2023
0helpful
1answer

My Ge washing machine is leaking from the Bottom

It leaksYour washer can develop several types of leaks. You can track down a leak based on when it occurs: 

During fill only
During drain and spin only
All the time

During fill only
If the washer leaks only during the fill cycle, check these:

Air-gap device -The air gap is a small device found on most washers that prevents the wash water from being siphoned into the household water supply. It's located either mid-way along or at the end of the black rubber hose that comes from the water-inlet valve. Often it's made of translucent plastic. If one of the air-gap components deforms or cracks, you may need to replace it.


The tube -There's a rubber tube that runs between the water-inlet valve and either the air-gap or the inlet spout. If it cracks or breaks, it can cause a leak. 


Inlet spout -Most washers have a plastic spout near the top of the main clothes tub that directs the water into the tub. If the spout cracks or breaks free of its mounting, it can cause a leak. 



During drain and spin only
A washer that leaks only during the spin cycle often has a leak in the main drain hose. Inspect the entire hose and correct any problem you find. Alternatively, the steel or plastic outer tubs can rust, split, or be punctured. This may be most visible during large loads and high water levels. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details. 


All the time
If the washer leaks all the time, check these:

Hot and cold water fill hoses - Check the hot and cold water hoses from the household plumbing. If either hose is leaking, tighten it or replace it, as appropriate.


Main tub seal - The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft entry point. If this seal leaks, you can see the leak by opening up the machine's main access panel while the machine is full of water with a small amount of detergent in it. The leak appears at the underside of the outer tub, at or near the center. This seal is difficult to replace. You probably should call a qualified appliance repair technician. 


Pump - If the pump leaks, you can probably spot the leak when the tub is full of water. The pump has two or more black rubber or plastic hoses attached to it and usually has a drive belt that spins the pump. If the pump is leaking, you need to replace it. 


Outer tub - Over time, the steel or plastic outer tubs can rust, split, or be punctured. If this happens, you may have to replace the entire outer tub--but that may not be an economical repair to make. Consult a qualified appliance repair technician for further details.

11/17/2023 2:59:32 PM • GE Profile... • Answered on Nov 17, 2023
0helpful
19answers

GE top load Washer ripping clothes

Solution!
GE has replaced the "boot" (the large rubber gasket at the opening of the washer) on my washer. This has fixed the problem!

Although the majority of people I spoke with at GE did not know about this, eventually I got a repair technician out here who spoke with one of the engineers. The engineer said that there was a problem with the boot causing clothing to rip. The new boot we have on our washer covers a ring of plastic just on the outside of the metal drum (the plastic rim remains stationary while the metal drum spins - this is the cause of the ripped clothing) - the old boot left this plastic ring exposed. Our washer was only 8 months old - so even if your washer is new, if your clothing is being ripped, insist that the boot be replaced for an updated version.

Good luck!
11/13/2023 6:51:52 AM • GE Energy Star... • Answered on Nov 13, 2023
0helpful
2answers

GE Washing Machine model GTW330ASK0WW. It won't run, no sounds, display comes on and after 15 seconds shuts down.

Question edited for clarity 'MAKE model (WHAT IT IS)'. You posted to Televisions, moved to GE Washing Machine. It may be the lid lock, test it with your digital multimeter. Look for loose or damaged connections. https://www.google.com/search?q=GE+Gtw330ask0ww+not+running ..
10/21/2023 3:04:17 AM • GE Washing... • Answered on Oct 21, 2023
0helpful
2answers

GE Washer model GFAN1000L2WW. Stucked during the washing process with no agitation.

check under agitator possible worn cogs
10/21/2023 3:02:47 AM • GE Washing... • Answered on Oct 21, 2023
0helpful
2answers

Why wont My ge washer drain

check voltage to pump if ok bad pump also check drain hose
10/21/2023 2:59:12 AM • GE Washing... • Answered on Oct 21, 2023
0helpful
1answer

Ge washer h20 supply error

Check the water level sensor.
10/12/2023 7:52:46 AM • GE Washing... • Answered on Oct 12, 2023
0helpful
1answer

Winterizing a washer in a summer cabin

Just remove the drain hose from the drain upstand pipe and lower it to the floor. It will empty the pump or water.You can also drop a pint of car anti freeze into the machine just to be sure if you wish.
10/10/2023 5:24:57 AM • GE Washing... • Answered on Oct 10, 2023
0helpful
1answer

Why is my GE front load washer breaking the circuit after it starts to fill with water?

You likely have a water leak spraying onto electrics, or the water inlet valve is shorting out.
10/1/2023 3:42:48 AM • GE Washing... • Answered on Oct 01, 2023
0helpful
1answer

Top Loader GE with impeller not agitator leaving oily looking stains

Remove the bottom impeller and clean out the water proof grease that has come out of the seal and drive shaft.
9/27/2023 5:16:31 PM • GE Washing... • Answered on Sep 27, 2023
0helpful
1answer

How to reset a GE washing machine WPDH8900J1WW

I understand your frustration. It sounds like your GE washing machine is having some problems. Resetting the washer may help to fix the issue. Here are the steps on how to reset a GE washing machine WPDH8900J1WW: 1. Unplug the washer from the power outlet. 2. Wait for 2 minutes. 3. Plug the washer back in. 4. Turn on the washer. 5. Select a cycle and press the start button. If the washer still does not work, you can try resetting the drum motor. To do this, follow these steps: 1. Unplug the washer from the power outlet. 2. Wait for 1 minute. 3. Plug the washer back in. 4. Open and close the lid of the washer 6 times within 12 seconds. 5. Close the lid and press the start button. If the washer still does not work after resetting the drum motor, you may need to contact a qualified appliance repair technician. Here are some other things you can try before resetting the washer: * Make sure that the washer is properly leveled. * Check the water supply hoses for leaks. * Clean the lint trap. * Check the detergent dispenser for clogs. I hope this helps!
8/27/2023 8:59:56 PM • GE Washing... • Answered on Aug 27, 2023
0helpful
1answer

How to get into service mode on my GE GFWN1600?

Please see the following link for the error codes https://www.youtube.com/watch?v=JglsX87UdeY&pp=ygUvSG93IHRvIGdldCBpbnRvIHNlcnZpY2UgbW9kZSBvbiBteSBHRSBHRldOMTYwMD8%3D
8/27/2023 1:11:33 PM • GE Washing... • Answered on Aug 27, 2023
0helpful
1answer

My GE top load washer model 110.27062603 will not run through a full cycle. Sometimes it washes, but 17 minutes showing, jumps to 2 minutes, then shuts off with 'OL' error code.

OL = Overloaded. Is the Washer overloaded? If OL (overloaded) appears in display, the load too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.Feb 24, 2020

OL - Error Code - Top Load Washer - Product Help - Maytag

Maytag https://producthelp.maytag.com > ... > OL

The washer has ol on it at the end - Maytag Bravos quiet ...

iFixit https://www.ifixit.com > Answers > View > The+washe... Oct 6, 2014 · 2 answers First, OL stands for "Overload", so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is ... OL code all the time even with very small and light ... 2 answers Sep 28, 2016 Why washer stops and gives code "ol" - iFixit 2 answers Nov 30, 2016 at the end it says OL - Maytag Bravos quiet series 300 ... 1 answer Dec 29, 2022 OL code showing . - Kenmore 110 Series Washing ... 2 answers Sep 19, 2017 More results from www.ifixit.com
7/14/2023 12:07:29 AM • GE Washing... • Answered on Jul 14, 2023
0helpful
5answers

WH45X10060 - is this a joke?

do you need just the hub or do you also need the basket...I can sell you a hub.. let me know
6/27/2023 8:16:19 PM • GE Profile... • Answered on Jun 27, 2023
Not finding what you are looking for?
GE Logo

9,586 questions posted

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Brad Brown

Level 3 Expert

19187 Answers

Virgil Watts

Level 2 Expert

267 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...