GE Recent Questions, Troubleshooting Help & Support

If it smalls 'fishy', it is overheating at the motor windings. That would not cause the dryers thermal fuses to trip. Dryers don't normally have an internal breaker. Remove the motor, strip and clean it. Lubricate the bearings. It should spin very freely.

Probably low on refridgerant. Time to call a refridgeration engineer in.

Found this video.... https://circuitboardmedics.com/wb27t10282-oven-control-board-repair/#instructional-video Sure hope it helps shows your model # Best to you

check these sites and give them a call at their 800#s to confirm with their techs https://www.repairclinic.com/PartDetail/Defrost-Timer/WR9X489/2578 https://www.appliancepartspros.com/repair-help/general-electric-refrigerator-tph21prsaaa-repair/tph21prsaaa-freezer-not-defrosting.html Best to you

It is very possibly a bad door gasket. ck here... https://www.repairclinic.com/ProductDetail/861053?symptoms=586 and here.... https://www.appliancepartspros.com/freezer-door-parts-for-ge-psh23pssbsv.html They both have very helpful techs at their 800#s. Best to you.

It is normal to build up frost at the Evaporator. The Automatic-defrost-System removes the Ice 3 or 4 times, every 24 hours.(de-frosting). 1 The Fan MUST rotate , inside. Is the Fan blowing Air inside,?? sometimes The door must be shut, then the fan-motor starts (,put your ear against the door when you close it and listen for the fan- noise,) There may be an Automatic-Defrost fault: Faulty : Defrost-Timer, (electro-mecanical) ( DT ) c. fault. Defrost-Heater,. ( DH ) common fault. Defrost-Termination-Timer,. ( DTT) (Over) Temperature-Fuse. ( TF ) If the Refrigerator has 'Electronic' controls, a Computer controls the Automatic Defrosting. A Temperature-Sensor replaces the DDT. A Computer-controlled timer replaces the DT ----- A Sensor faulty? -----Control Board (Computer) faulty. Common fault. I found,- To read and remember is easy. To 'understand' takes a little more time . To practice, improves my skill, With skills, it is easy to perform the task. Experience has build up my skill & confidence. Wisdom is, when I admit that I require additional knowledge. (Happiness is a result of sharing and caring. That's why I am happy.) K.

Strange it won't turn back on. Did you see it working when you purchased it secondhand? It appears you just need to reset. Turn off at the breaker for 2 minutes, then back on and try this.

SOLVED: Our GE Profile JTP18 keeps flashing "door loc

Fixya https://www.fixya.com > support > t200245-our_ge_p... 6 answers If the oven is flashing "LOCKED DOOR" on the display. even though the door is open, the fix is easy and there is no need for repair. Press and hold the oven ... https://products.geappliances.com/appliance/gea-support-search-content?contentId=16196 lots more here https://www.google.com/search?q=GE+jtp15+wall+oven+locked+door+flashing%2C+4%3A00+flashing ..

The rotary start switch? $41 here https://www.appliancepartspros.com/search.aspx?model=dde5100ralwh $45.50 here https://www.repairclinic.com/ProductDetail/48411 With Google search queries, less words are better! https://www.google.com/search?q=DDE5100RALWH+switch ..

There is no set-up codes to this brand TV with GE remote control. If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name" in alphabetical order. Pull up older posts. Surf the site with patience. Surf the sites by type in the brand name to your set, in its search box. http://electronicshelponline.blogspot.com/ http://remotesearch.blogspot.com/ http://electro-medical.blogspot.com/ http://electrohelponline.blogspot.com/

Maybe this will help you.... https://www.appliancepartspros.com/microwave-parts-for-ge-peb1590sm2ss.html They have a 800# too call and confirm the part and disguss your issue. Best to you.

Question edited for clarity, full 'make model (what it is)'. Question moved from Cars and Trucks. They all work to a theme. Normally you start from the back, remove the lid and then the front.

It looked like your model does NOT have an external ice/water control panel which has caused beeping problems on some models. For your model I would try the following.... Door Alarm The main cause of a beeping GE unit is an open refrigerator door. Some models are equipped with an internal door alarm, which trips when the door remains open for 3 minutes or longer. One way to check this .... put your smartphone in the refrigerator on video mode and close the door. The light should go off with the door shut. If the video shows that the light stayed on when the door was closed ... then it reinforces that something is wrong with the switch/alarm. Repeat video for the freezer. Door Seal If beeping persists after the freezer or refrigerator door is closed, the door seals may be blocked or so dirty that the internal door alarm is tripped. The seals can be cleaned with a soft cloth and warm, soapy water. Also, an item inside the refrigerator may be preventing the door from fully closing. Cooling System Reactivating the refrigerator's cooling system includes a beeping noise. When the refrigerator is off, the "Off/Off" light appears on the door display. When the "Adjust Freezer" and "Energy Saver" buttons are held down for approximately 3 seconds at the same time the beep sounds and the "Off/Off" indicator disappears. Hold the "Ice Off" and "Freezer" buttons to activate the cooling system inside of the fresh food compartment. A beep signals the system is activated. The beeping should stop after the cooling system turns on. If it fails to stop, try unplugging the power cord to reset the connection. Power The GE's internal door alarm can get stuck. Try unplugging the refrigerator for about 10 seconds and then plug it back in. If the beeping continues, the internal door alarm might be broken or defective. Contact the manufacturer or a technician for further assistance. One way to check this .... put your smartphone in the refrigerator on video and close the door. The light should go off with the door shut. If the video shows that the light stayed on when the door was closed ... then it reinforces that something is wrong with the switch/alarm. Good luck on your troubleshooting!

Impossible to say. There are a lot of variables here. Which country, and which model. Even different cities would charge different prices. It is a gas appliance, so you can't work on it yourself. Just for information, we are Fixya dot com, we aren't GE, we don't do pricing for them. The only way is to ask a local appliance shop. A good way is to ask for a recommendation on a local Facebook group where you live.

Here are some possible causes and solutions to consider: 1. Check the temperature settings: Ensure that the temperature settings are set to the recommended levels for your refrigerator. You can refer to the user manual or manufacturer's website for the recommended temperature range. The target range is between 35-38°F 2. Clean the condenser coils: Dirty or clogged condenser coils can prevent the refrigerator from cooling properly. Clean the condenser coils located at the back or bottom of the refrigerator using a vacuum or brush. 3. Check the evaporator fan: The evaporator fan circulates cool air throughout the refrigerator and normally runs constantly. If it's not functioning correctly, it can cause the refrigerator to stop cooling. Check that the fan is running and for any obstructions or damage and replace it if necessary. 4. Check the door seals: The door seals ensure that the refrigerator is properly sealed, preventing warm air from entering. Check the seals for any cracks, gaps or damage and replace them if necessary. 5. On many Fridge Freezers, the cold air for the fridge is vented from the freezer side into the fridge. If the freezer coils ice up or block due to faulty defrosting, it can cause no cold air to reach the fridge compartment. 6. Checking the refrigerant gas levels: If the refrigerant levels are low, the refrigerator will not cool properly. Only qualified technician can check the refrigerant levels and add more if necessary. ..

That will be because the static was at the callers line, not at your end. At this time of year it is water in junction boxes at the caller's residence. If it was on every call, it would be down to your connections.

yourspacebarisbroken,editinnsomespaces! Wecan'tpossiblyanswerquestionslikethis!

Make sure the hot water is on

This is a old post but may answer your issue....https://forum.appliancepartspros.com/posts/t537870-ge-profile-ice-melting-then-refreezingBest to you.The part i believe...https://www.partselect.com/PS2371164-GE-WR55X10996-BOARD-Assembly-MAIN-CONTROL.htm?SourceCode=20&SearchTerm=GFSS2HCYHSS&ModelNum=GFSS2HCYHSS&ModelID=1923343looks like you'll have to copy and paste.

Greetings, If the mechanism of the button pushing in automatically is what allows the wash cycle to stop, then you can apply some oil to the area of the button that touches the rest of the washer. Friction could be stopping the normal mechanism which would be one cause of the continuous, spin cycle issue that you're experiencing. Thank you.

Either the drain hose is or the pump could be clogged or plugged.Or it needs a new drain hose or a new pump for your washing machine.