Galaxy Radio Communications - Recent Questions, Troubleshooting & Support


could be a number of problems,final being one of them.Could be a bad match to your antenna . could be a bad transformer or a rectifier . If you have no electronic knowledge take it to a tech a let them work on it. Could save you some money .

Radio... • Answered on Mar 05, 2021


The setting methods of the wireless extender are similar, but are briefly summarized as follows: 1. Place the wireless extender in a suitable position between the main router and the weak signal area to supply power. 2. The mobile phone or laptop searches for the signal of the extender and connects the signal. 3. Enter tplogin.cn in the browser to log in to the extender interface and set an administrator password. 4. Follow the setup wizard, scan the signal, select the signal to be expanded, enter the wireless password, and save the settings. (The single-frequency wireless extender only scans the 2.4G wireless signal of the extender, and the dual-frequency wireless router will scan the 2.4G and 5G wireless signals respectively.) http://121.14.139.246:8082/cms/keditor/themes/common/blank.gif5. After the expansion is completed, observe the indicator light of the wireless extender. Orange or green indicates successful expansion. (If the indicator light is orange, adjust the position of the extender appropriately) After the expansion is successful, the wireless terminal can connect to the expanded wireless signal to access the Internet. During the movement of the terminal, automatic roaming between the main router and the extender can be realized.

Galaxy Radio... • Answered on Jan 04, 2021


Request the manual from Galaxy.

Galaxy Radio... • Answered on Dec 22, 2020


if the company or your local dealer can not help then you might never get one

Galaxy Radio... • Answered on Dec 10, 2020


Find a schematic, watt meter & proper tuning tools first. Now tune or peak the SWR on the coax & antenna used by the radio. The SWR function in the radio may do. When adjusting do so VERY SLOW and only in the RF power out circuit. NO! You don't need a FCC license to do this. May the force be with you.

Galaxy Radio... • Answered on Apr 24, 2020


Inside of the cabinette there is a small pc board located on the right side of the chasis. It sits vertically and has a metal cover on it. There are 2 potentiometers on the board. One is for depth of echo and the other is for speed)

Radio... • Answered on Mar 20, 2020


Here are the pinouts for the 4 wire and 6 wire D104 mics. they were great microphones back in the 1980s. I used to have one on my Ten-Tac HF ham radio. Astatic (4 wire) Astatic (6 wire) 1- Shield 1- Shield & Blue 2- White 2- White 3- Red 3- Red 4- Black 4- Black Yellow NC you just need to know what the pin out is for your 10M Radio. here is what each pin is 4 WIRE MIC CABLE Pin Number 1 Audio Shield 2 Audio Lead 3 Transmit Control 4 Receive Control here is the manual. https://www.manualslib.com/manual/452637/Galaxy-Dx-98vhp.html?page=8#manual

Galaxy Radio... • Answered on Oct 03, 2019


Each channel is a AM carrier frequency which is the center frequency of the channel. Each AM frequency has two sidebands, a lower sideband which is the below the center frequency (AM) and a upper sideband which is above the center frequency. See the following for some explanation of sidebands: https://en.wikipedia.org/wiki/Sideband Hope this helps and 73 Jim

Galaxy Radio... • Answered on Aug 29, 2019


It sounds like you either have a mis-matched antenna, a poor antenna connection, or your radio is too close to the antenna. Try moving the radio further away from the antenna.

Galaxy Radio... • Answered on Jun 04, 2019


Google found this on the Galaxy site: https://sites.google.com/site/galaxyradios/amateur-and-cb-radios/amateur-radios/galaxy-dx-47hp

Galaxy Radio... • Answered on Jun 04, 2019


check out www.cbradio.nl:servicemanual they have a Saturn and it should be the same as the turbo . Good luck.

Galaxy Radio... • Answered on May 23, 2019


The diode audio limiter is detecting when your audio levels are too high and clips the audio waveform, limiting the strength of the signal before it is further amplified by your audio amplifier. When the diode audio limiter is working, it is therefore helping eliminate static and pops that are annoying, and keep you from clearly hearing the desired signal.

Galaxy Radio... • Answered on Apr 08, 2019


This involves checking the voltages on the internal final and driver transistors. The base connection should have 4 to 6 volts on it..

Galaxy Radio... • Answered on Feb 01, 2019


I hope you have the right equipment to work on this. http://www.cbtricks.com/radios/galaxy/dx99v/ If it was modded you may be in for a long haul. There are a lot of youtube vids on how to mod radios and not many of them do it correctly. Good luck

Galaxy Radio... • Answered on Feb 01, 2019


I would check the wires and push to talk switch for your microphone. Likely the continuity is broken due to either a broken connection at the plug, the wire itself, or the push to talk switch. Use an ohm meter with the microphone unplugged and put the two test leads of the ohm meter across the two pins on the microphone plug that controls the on off function. When you press the push to talk switch if the ohm meter does not read near zero ohms, your problem is in your mic connections,

Galaxy Radio... • Answered on Jan 25, 2019


the switch with E/A, F/B, G/C, H/D is the band selector. the switch with PA, FM, AM is the mode selector. use this switch if you want to work on FM or AM. here is a link if you want to download the manual: http://cbradio.nl/galaxy/Manual_Galaxy_DX44V_ENG.pdf

Galaxy Radio... • Answered on Nov 14, 2018


what no directions with it ?To program sounds into it ,if I am not mistaken , there is a microphone that comes with it to pick up anything you want to record but I think it will cover up your last sound . I have never owned one or installed one but there should have been instructions with it .

Galaxy Radio... • Answered on Oct 04, 2018


the problem is one you may not be able to work on . It will take a scope and a spectrum analyzer along with an RFSG to get this one working . Some simple ??. Does the radio come on ? Check with your hand passing over the radio to check for hot spots? The best thing to do is get it to a tech and let them work on it.

Galaxy Radio... • Answered on Oct 04, 2018


make sure the voltage switch on the back of the radio is fully into the position you are using it for. it has an a/c switch and 120 volt on the same switch .

Galaxy Radio... • Answered on Oct 04, 2018


vr 13 AM high power and VR 16 am low power

Galaxy Radio... • Answered on Oct 03, 2018

Not finding what you are looking for?
Galaxy Logo

51 questions posted

Ask a Question

Usually answered in minutes!

Top Galaxy Radio Communications Experts

Lawrence Oravetz

Level 3 Expert

10548 Answers

Vernon Taylor

Level 3 Expert

7446 Answers

Brad Brown

Level 3 Expert

18632 Answers

Are you a Galaxy Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...