Frigidaire Kitchen Ranges - Page 4 - Recent Questions, Troubleshooting & Support

Dear IFE KIARA, Warning: If you feel in any way uncomfortable/unsafe performing this test or making this repair, please contact a qualified appliance repair technician. F13 error is related to the clock. this error can occur when the clock looses communication between the keypad or any of the sensor in the stove, including the heat probe. sometimes resetting the power will fix the problem. Try disconnecting power to the stove completely and flip the corresponding breaker on and off at the breaker box. Wait 30 seconds and then turn everything back on. if the problem persist after power-up, according to Frigidaire suggested corrective action the electronic oven control,also called EOC has to be replaced. Here is a search link from Google for the part in question. Best of Luck, JP https://www.google.com/search?source=hp&ei=fecFXYCMAsKr5wKBm6G4DQ&q=316418735&oq=&gs_l=psy-ab.1.0.35i39l10.0.0..5525...1.0..0.209.209.2-1......0......gws-wiz.....10.8VUU1xaL8qM

What is the model number?

How can I take my frigidaire gas range out of demo mode

Yes, the microwaves will still be contained,however it needs to be replaced. super glue will work if the original parts are broken or lost

The F50 code appears to indicate that the oven relay board can't get the status of the switches (door closed, motor door lock). Try unplugging the range to reset the control board. Next check the wiring harness. If there is nothing wrong with the wiring, then the oven relay board may be faulty. Please add a comment with the model of the Frigidaire range if you would like a parts diagram and other information. I hope this helps. Cindy Wells

The gas orifices for propane are different than LP gas. Are you trying to blow yourself up?

THAT CODES MEANS EITHER THE PROBE SENSOR OR THE ELECTRONIC CONTROL IS BAD. UNPLUG. WITH WIRING DIAGRAM AND OHM METER, TEST THE TWO WIRES GOING TO PROBE. IF YOU GET ABOUT 1100 OHMS, YOU HAVE A BAD CONTROL. IF YOU GET 0 OR INFINITY, IT'S THE SENSOR OR THE WIRES BETWEEN THE PROBE AND THE CONTROL

[email protected] OR 714-334-1998. I CAN WALK YOU THROUGH IF NEEDED

SOUNDS LIKE YOU HAVE A REGULATOR PROBLEM. IT WONT HURT ANYTHING ITS JUST ANNOYING. OR YOU CAN REPLACE THE REGULATOR If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

It is not based on time,. It uses temp sensors. When surface is cool enough it will go out..

This is going to require a new EOC, which is the control board. I attached a link that may help.

The first thing we want to do is disconnect all power to the range for 5 minutes. Turn the power back on and test. If that does not work it could be the induction generator or the relay board it would take some electrical testing to figure out which. I hope this was some help.

Code D81 is usually caused by a power surge of some type. The first thing to try is to unplug or shut off the power to the unit for 5 minutes and try it again.

That is a power fault. Your control board is bad.

Where is the office at to make the oven and smaller

1.Try disconnecting the electricity for 20 seconds, shut off the breaker in the breaker box to the oven. Then restoring it. 2.Try setting the oven into clean and starting it. Wait 30 seconds and cancel clean. Sometimes one of these methods work. Best to you

I suggest you lift off the burner ring and ensure there is no foreign matter in the area of the igniter. Observe whether the is a spark when you press the button to light the gas. It is possible that the ignition plug has failed, therefor you will need to purchse a replacement.

Shorted touchpad. Try unplugging for 5 minutes to see if it will reset

Here’s the link to Frigidaire answer center.

https://www.frigidaire.com/Owner-Center/Contact-Us/

just started 6 weeks ago and I've gotten 2 check for a total of $2,200...this is the best decision I made in a long time! "Thank you for giving me this extraordinary opportunity to make extra money from home. This extra cash has changed my life in so many ways, thank you!" Visit site:: SalaryHD­­.­­C­­o­­m