Frigidaire Dryers - Recent Questions, Troubleshooting & Support


Hello Becky; My name is Peter. I am a retired field service appliance technician. E65 = High limit thermostat trip count too high. In other words, you probably have a restricted air flow problem. Your blower will shut down if your plugged up with lint. In the back of your dryer is a hot air distribution manifold. At the bottom of the manifold is a small round connection. This is generally where the dyer air flow is blocked. There are only a few screws holding it on. Un plug your unit, remove the hot air distribution manifold, Clean the manifold and around the blower wheel. Turn the wheel by hand to ensure it is not stuck and free. If this is not the problem, get back to me and we will talk about the high temperature thermostat. 25348525-v2tfx3vduhdvisabvvbtnvyp-5-0.jpg

Frigidaire... • Answered on May 03, 2021


Sounds like the door switch is bad and the unit is acting as if the door is still opened even when you have it closed. Here is the switch for your unit.
1_28_2021_3_41_27_am.png

Frigidaire... • Answered on Feb 28, 2021


Did you hold button for at least 5 seconds?

Frigidaire... • Answered on Dec 11, 2020


Frigidaire Affinity dryer model AEQ7000ESO error code E68 (stuck button). Sometimes a 'stuck button' code really is a stuck button. I took the circuit board off the front panel.On the back side of the front panel, each button has 3 short plastic posts, 2 on one side and 1 on the other.The center part moves to push a longer piece that contacts the circuit board. When I push the top of a front stadium-shaped button, the center plastic piece moves too far, touches the short post, and sticks (maybe due to age). When I push the bottom of the front button, the plastic piece goes far enough to contact the circuit board and not far enough to touch the short post. To prevent a stuck button, we now press the bottom of the front buttons.So far so good. If it happens again, I plan to shave or file a little bit off the top edge of the post to give it more clearance. 1st photo: pencil points to stuck parts. 2nd photo: unstuck parts, 3rd photo: the front of our dryer. 68a7d368-523a-4ad9-b13a-20009dc9f567.jpg

Frigidaire... • Answered on Nov 12, 2020


this is a fault code that means there is a stuck key on the board you may have to remove the control panel and check the keys if this does not work you may have to replace the panel or control board

Frigidaire... • Answered on Nov 04, 2020


One of the buttons is stuck closed or shorted. Enter the function test mode and perform the button test to determine which button is stuck or shorted. When determined which button, try to free or unstuck the button then perform the test again. Replace the user interface board when the button is freed but the code still exists.

Press and hold the SELECT and CANCEL buttons simultaneously for 6 seconds to reset the control. When resetting is successful, the buzzer will sound and "rES" will be shown briefly in the display, and then immediately rotate the cycle selector knob 5 turns in the counterclockwise direction to the second position from the bottom.

Press and hold the OPTIONS and CANCEL buttons simultaneously for 2 seconds to enter test mode; the buzzer will sound 3 times and all of the LEDs will flash rapidly.

Rotate the cycle selector knob 4 times in the clockwise direction to enter button test. Press the buttons one at a time and observe the LEDs corresponding to that button light up. The LEDs should light up; otherwise the button is stuck.

Press and hold the SELECT and CANCEL buttons simultaneously for 6 seconds to exit test mode.

Frigidaire ... • Answered on Nov 04, 2020


Please click the link below to see my answer to a similar E68 question on fixya:https://www.fixya.com/support/t10225683-error_code_e68_frigidaire_affinity

Frigidaire... • Answered on Nov 03, 2020


check your dryer vent system, may be blocked causing the dryer to over heat and turning off so there won't be a fire.

Frigidaire... • Answered on Oct 21, 2020


sounds like the control board, is there any codes displayed?

Frigidaire... • Answered on Oct 20, 2020


E61 is a stuck relay on the main control board. This is the board right behind the control panel where all the buttons are. You'll need to order and replace this board.

Frigidaire... • Answered on Sep 19, 2020


The fault often lies with the motor relay because the motor relay should keep the dryer running after you release the push-to-start switch. The following page has a link to a video providing a tip to restarting the dryer. That said, the troubleshooting page points out that door latch problems can also be a cause of stoppages. https://www.searspartsdirect.com/diy/symptom/dryer-repair/1234594/starts-then-stops/dryel09

Frigidaire... • Answered on Sep 19, 2020


Control board problem. Unplug the dryer for 5 minutes to reset the control board. Plug the dryer in and start a cycle. If the code appears, replace the electronic control board. https://www.searspartsdirect.com/diy/error-codes/dryer-repair/1234594/frigidaire-dryer/1428

Frigidaire... • Answered on Sep 19, 2020


PAU (pause) may reflect an excessive load or one out of balance. Or, it may indicate the exhaust hose is blocked, crimped or smashed (something you can check by pulling out the dryer, disconnecting the hose and seeing if the dryer then works). Burt before you do any of this, you can simply unplug and replug the dryer. Like a computer, that is sometimes all you need to do. But if this is a control board problem, other than jiggling such or checking for a loose wire, you will have to have a service tech look at it. I am assuming that the door latch is working.(which operates a sensor).

Frigidaire... • Answered on Sep 19, 2020


E68 for this model number says in manual that this is for a "button stuck" or held down for more than 30 seconds ck all your buttons for one that just doesn't "feel right" when its pressed , this one will be your problem

Frigidaire... • Answered on May 15, 2020


Sounds like you have a stuck button. Try removing the panel and putting it back on. Worst case scenario- you may have to replace it. Then you'll have a happy Frigidaire appliance again. Frigidaire Appliance Repair EZ Fix Appliance Repair Las Vegas

Frigidaire... • Answered on May 15, 2020


PF is showing you that there is a power problem. Check your dryer circuit breaker at the power panel. This can be a sing that one of the 2 breakers has tripped. Push the CB hard to OFF and then back to ON. Then try and start your dryer. If that does not work just respond here and I will help you.

Try selecting "No Heat" after resetting the CB and see if the dryer starts. If it does you could have a bad heating element that caused the breaker to trip to begin with. Sometimes when the heating element fails the broken link will contact the chassis and cause the CB to trip. Heating element failures are usually caused by poor airflow. You may want to look for any signs of lint in your dryer to include the lint filter area and all the way to the outside wall exhaust point.

Kelly

Frigidaire ... • Answered on May 13, 2020


ELECTRICDryer no heat or little heat, or shuts down to fast: Checkyour venting and lint basket. Check blower for lint build up and blower wheel obstruction., test by trying to turn the wheel manually by hand (should be easy) May have to remove cabinet or front/back plate to get to it) Next check the heating element itself with a meter for continuityit should showOHMS CLOSED CIRCUIT. If not its defectiveor has a short if its grounding out? Which in turns causes blown fuses or thermostats or overheating. The heating elements are located inside the heater ducts. If you think a heating element is faulty, test it with avolt-ohm-multimeter(VOM)set to the RX1 scaleat 20K ohms. Disconnect the leads from the power terminals and clip one probe of the VOM to each terminal. The meter should read about 12. (1200)ohms.If the reading is higherohms, the heater is faulty and should be replaced. Replace a faulty heater with a new one of the same type and electrical rating. A heater connected to a 115-volt line usually has an 8.4-ohm resistance; a heater connected to a 220-volt line usually has 11 ohms resistance. Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage. 220 because if u only get half or 110 volts you will be able to run the machine which uses only 110 to run motor but not the heater which uses a full 220,OR?you may have a broken centrifugal switch in the motor because this switch activates the motor and the heater as well. supposedto be if the motor does not run, the heater should not heat in order not to createafire but ifthe motor is not running,andthe heater is still heating, then there could be a problem with the motor centrifugal switch that is connected to this interlock switch that should trigger the heater. Check the thermal cut off, the cycling and the hi limit thermostats. For continuity or OHMS. If no ohms or resistance they need replacement. In somedryer'sthecontrol panel relies on athermistorrather than aCYCLING thermostatto regulate the drum's air temperature by monitoring the component's resistance changes; resistance goes down as temperature increases and up when temperature decreases. Once the drum's air temperature reaches a certain level required to dry clothes, the control panel shuts off the heater. The panel will turn the heater on again and begin another heating cycle when thethermistorindicates that more heat is needed to keep the air temperature constant inside the drumthis is why in some cases the dryer will operate at lower cycles like gentle or low heat but not at higher settings?) Lastly check your moister sensor.( located inside the dryer door usually) Especially if machine seems to shutdown early and clothesare still wet. Test with a meterat room temperatureand it should show continuity. A failed moisture sensor will affect the dryer run timein the automatic moisture sensing cyclebut it will not affect the heatingof the dryer or the timed cycle.Which are reflected by the thermostats. Read more : https://www.youtube.com/watch?v=wVTBrGMql7g http://www.ehow.com/info_12203962_check-dryer-thermistor. GOD IS So GOOD !!!!AND THAT'S WHY MY ADVICE IS FREE https://www.youtube.com/watch?v=MMP7BW1lLs4 vent tube bad -undefined-undefined-0_1.jpg vent outside dryer vent buildup-undefined-undefined-2.jpg vent clogged vent tube-undefined-undefined-5.jpg venting in cabinet clogged-undefined-undefined-9.jpg test dryer element-undefined-undefined-14.jpg

Frigidaire... • Answered on Mar 28, 2020

Not finding what you are looking for?
Frigidaire Logo

4,823 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...