Fossil BQ - Popular Questions, Answers, Tips & Manuals

Try this link Luis, FOSSIL watches handbags accessories and apparel www fossil com

To save paper you need to download it now Paper is bad for the environment so I have been told

try this link below http://www.fossil.co.uk/wcsstore/CommonFossil/attachments/watch_instructions/Fossil_Watch_Instructions_ENG_UK.pdf

Some watches sit for several years before they are sold and if the battery is old or happens to be activated during that time your battery will be close to being shot when you buy it. I would put a new battery in it and see how long it lasts . I would bet that's what happened.

go to this link for instructionshttp://www.fossil.co.uk/wcsstore/CommonFossil/html/int.html

click this link for instructionshttp://www.fossil.co.uk/webapp/wcs/stores/servlet/ContentView?page=customerCare_watchInstructions&storeId=32553&catalogId=25005&langId=10

Lots of possibilities. One is they put in a dead battery, don't laugh. I have seen this several times. Two, the watch has a problem other than the battery and you assumed the problem was the battery when actually it is something else. I have more but these two are the obvious. Find a watchmaker.

go to the link below for instructionshttp://www.fossil.com/wcsstore/CommonFossil/attachments/watch_instructions/Fossil_Watch_Instructions_ENG_UK.pdf

The light is only powered by the battery. The watch itself has many moving parts and probably has some kind of mechanical issue.

Fossil do not have a list of instructions under model numbers but issue a list of generic instructions which you have to wade through to find the one that suits your watch.

Go to http://www.fossil.com/en_US/shop/customer_care/static/fossil-Instructions.html and put your cursor over each of the ones listed in the Multifunction section until you reach the one that looks nearest yours and download the file.

Go to your nearest "Batteries Plus" store, they have just about every battery under the sun and they'll install it for you FREE

For removing or adding links firstly you will have to remove bracelet pins or screws. In case if there are screw on each side of bracelet - you have to use two screwdrivers simultaneously. In case if there are pins - read the rest:
You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out. First you have to find out what sort of pins or even screws are used to keep links together (screw ends and pin end may look similar). Examine both bracelet sides and find the side where pin ends have a groove. Start with a tiny screwdriver and try to unscrew one. If it turns, but doesn't come out, that means you have a pins instead of screws. For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it. Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well. NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer. Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows. After a few punches check if the split end is coming out and when you see that the pin end is coming out long enough - grab it with pliers and pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting. After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet. It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin. Make sure that pin ends are flush with bracelet. If needed- hit few more times. Job done! If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.

Thank you for contacting FixYa.
Pull the crown out to position No. 3, turn clockwise to go to hour and minutes hands; the small dial showing days of the week will move, and the 24-hour dial will also move correspondingly.To set the date, pull the crown out to position No. 2 and turn clockwise until you have set the desired date; push the crown back to position No. 1.

Multifunction watch:Pull the crown out to position No. 3, turn clockwise to go to hour and minutes hands; the small dial showing days of the week will move, and the 24-hour dial will also move correspondingly.To set the date, pull the crown out to position No. 2 and turn clockwise until you have set the desired date; push the crown back to position No. 1.

Thank you for contacting FixYa.

Identify the push button that controls the second hand. With the watch face positioned so that 12 is at the top, locate the button on the right of the watch's rim and above the watch stem.

2

Grasp the watch stem tightly and tug it out, away from the watch rim. Pull it past the first area of resistance, a position used for other settings, to the second stage of resistance where it will not pull out any further.

3

Press the second hand push button, identified earlier, until it is firmly depressed into the watch rim. Release the button, allowing it to return to its normal position.

4

Push the watch stem back to its original position tight to the rim.

Jewel

Check for manual/instructions here:

http://www.fossil.com/en_US/shop/customer_care/static/fossil-Instructions.html

Sometimes these watches have 2 batteries. One for the digital & one for the hands.

mcdevito75 here, You may need to start your watch by pressing the MODE button. Most quartz watches will stop once you"ve changed the battery, of course the possibility is there that the watch quartz has burnt out also. See a small watch repair shop in your area.

mcdevito 75 here, Check directly with Fossil on line for the manual, or check with your local watch repair shop.

mcdevito75 here, Look for any Notch in the cover that match a notch in the case, use a knife with a sharp blade and place the knife in the notch and with a slight twisting motion the cover should pop off. Depending on the age of the watch and the functions cost could be anywhere betwwen $25.00----$60.00 Fossil watches are also collectables.

cONSULT WITH THE EXPERTS